- 23 Jul, 2014 9 commits
-
-
Heiko Schocher authored
add basic support for the pwm modul found on imx6. Pieces of this code are based on linux code from drivers/pwm/pwm-imx.c Commit "cd3de83f1476 Linux 3.16-rc4" Signed-off-by:
Heiko Schocher <hs@denx.de> Acked-by:
Stefano Babic <sbabic@denx.de> Cc: Wolfgang Denk <wd@denx.de>
-
Heiko Schocher authored
add defines for pwm modul found on imx6. Signed-off-by:
Heiko Schocher <hs@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
Heiko Schocher authored
add IOMUXC_GPR1_USB_OTG_ID_OFFSET and IOMUXC_GPR1_USB_OTG_ID_SEL_MASK define for the USB_OTG_ID_SEL bit. Signed-off-by:
Heiko Schocher <hs@denx.de> Acked-by:
Stefano Babic <sbabic@denx.de>
-
Marek Vasut authored
As a result of 0defddc8 , which did a consolidation of the prompt string, this ifdef became empty. Remove it. Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Stefano Babic <sbabic@denx.de>
-
Fabio Estevam authored
On mx6solox there is an additional 0x4000 offset for the GPR registers. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Acked-by:
Stefano Babic <sbabic@denx.de>
-
Fabio Estevam authored
There is no need to keep iomuxc_base_regs structure as it serves the exact same purpose of the iomuxc structure, which is to provide access to the GPR registers. The additional fields of iomuxc_base_regs are not used. Other advantage of 'iomuxc' is that it has a shorter name and the variable declarations can fit into a single line. So remove iomuxc_base_regs structure and use iomuxc instead. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Acked-by:
Stefano Babic <sbabic@denx.de>
-
Fabio Estevam authored
Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com>
-
Fabio Estevam authored
The PFD issue is not present on mx6solox, so skip it in this case. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com>
-
Iain Paton authored
Enable CONFIG_SYS_GENERIC_BOARD to remove warning on boot. Signed-off-by:
Iain Paton <ipaton0@gmail.com>
-
- 16 Jul, 2014 1 commit
-
-
git://git.denx.de/u-bootStefano Babic authored
Signed-off-by:
Stefano Babic <sbabic@denx.de> Conflicts: boards.cfg
-
- 14 Jul, 2014 5 commits
-
-
Tom Rini authored
Signed-off-by:
Tom Rini <trini@ti.com>
-
Pavel Machek authored
Timer on cyclone5 actually counts down. It took me a while to figure out, as timer counting in wrong direction actually _can_ be used, it just appears to tick at extremely high frequency in u-boot. The bug was introduced in commit 23ab7ee0. Signed-off-by:
Pavel Machek <pavel@denx.de> Acked-by:
Marek Vasut <marex@denx.de>
-
Lokesh Vutla authored
Update the board_name env variable and accordingly populate the dtb file. Signed-off-by:
Lokesh Vutla <lokeshvutla@ti.com>
-
Masahiro Yamada authored
In the previous commit, all the board fields were filled. Now we can use "-" in the board field for a different meaning. Going forward, "-" stands for no board directory as in cpu, soc, vendor fields. Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
Masahiro Yamada authored
The boards.cfg file has allowed to use "-" for the board (= 6th) field if the board name is the same as the 7th field. But I notice one problem. Because tools/reformat.py sorts the lines in the simple alphabetical order (= the order of character code), some entries for the same board are not lined up together. For example, "bf527-ezkit" and "bf527-ezkit-v2" share the same board. But they are located separately because "bf527-ezkit" fills the board field with "-" whereas "bf527-ezkit-v2" specifies it explicitely. The similar things can be seen: - between "trizepsive" and "polaris" - between "RRvision" and "RRvision_LCD" - between "korat" and "korat_perm" - between "lwmon5" and "lcd4_lwmon5" This commit was generated by the following command: awk '$6 == "-" { $6 = $7 } { print }' boards.cfg \ | tools/reformat.py -i -d '-' -s 8 > boards0.cfg; \ mv boards0.cfg boards.cfg Signed-off-by:
Masahiro Yamada <yamada.m@jp.panasonic.com>
-
- 11 Jul, 2014 1 commit
-
-
git://www.denx.de/git/u-boot-imxTom Rini authored
-
- 10 Jul, 2014 5 commits
-
-
Fabio Estevam authored
Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com>
-
Fabio Estevam authored
mx6sx does not have sata nor ipu blocks, so do not handle such clocks. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com>
-
Fabio Estevam authored
Add the pin definitions for mx6sx. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com>
-
Fabio Estevam authored
mx6solox is the newest member of the mx6 family. Some of the new features on this variants are: - Cortex M4 microcontroller (besides the CortexA9) - Dual Gigabit Ethernet Add the initial support for it. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com>
-
Eric Nelson authored
The pad settings for DISP0_DATA02 and DISP0_DAT10 were not set in the same way as DISP0_DAT00-23, causing much flicker in parallel RGB displays on Dual-Lite and Solo processors. These settings now match the i.MX6 Dual and Quad core versions. Note that this fixes a regression in commit b47abc36 and that this is the second time we've had a regression on these two pads (See commit e654ddf7). Signed-off-by:
Eric Nelson <eric.nelson@boundarydevices.com> Acked-by:
Otavio Salvador <otavio@ossystems.com.br>
-
- 09 Jul, 2014 13 commits
-
-
Felipe Balbi authored
Newer AM437x silicon requires us to explicitly power up the USB2 PHY. By implementing usb_phy_power() we can achieve that. Signed-off-by:
Felipe Balbi <balbi@ti.com>
-
Felipe Balbi authored
some boards won't work if the PHY isn't explicitly powered up. Signed-off-by:
Felipe Balbi <balbi@ti.com>
-
Michal Simek authored
This is a MIME GnuPG-signed message. If you see this text, it means that your E-mail or Usenet software does not support MIME signed messages. The Internet standard for MIME PGP messages, RFC 2015, was published in 1996. To open this message correctly you will need to install E-mail or Usenet software that supports modern Internet standards. Signed-off-by:
Michal Simek <michal.simek@xilinx.com>
-
Lokesh Vutla authored
Updating omap4_sdp/panda and omap5_uevm maintainer. Signed-off-by:
Lokesh Vutla <lokeshvutla@ti.com> Acked-by:
R Sricharan <r.sricharan@ti.com>
-
git://www.denx.de/git/u-boot-imxTom Rini authored
-
Fabio Estevam authored
Commit 3d622b78 (mx6: soc: Introduce set_ldo_voltage()) introduces set_ldo_voltage() function that can be used to set the voltages of any of the three LDO regulators controlled by the PMU_REG_CORE register. Prior to this commit there was a single set_vddsoc() which only configured the VDDSOC regulator. Update the comments to align with the new set_ldo_voltage() implementation. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com>
-
Andre Renaud authored
DIV_SELECT is used as Fout = Fin * div_select / 2.0, so we should do the shift after the multiply to avoid rounding errors Signed-off-by:
Andre Renaud <andre@bluewatersys.com>
-
Lothar Rubusch authored
Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Lothar Rubusch <lothar@denx.de> Signed-off-by:
Wolfgang Denk <wd@denx.de>
-
Marek Vasut authored
Adjust the mtdparts settings to allow for alternative boot images and for using UBI. Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
Marek Vasut authored
- "env ask", "env grep" and "setexpr" are needed for commissioning - add support for ext4 file systems - adjust default environment to use ext4 commands - add write support for (V)FAT and EXT4 - add bitmap and splashscreen support - print timestamp information for images Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Wolfgang Denk <wd@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
Lothar Rubusch authored
Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
Lothar Rubusch <lothar@denx.de>
-
Marek Vasut authored
Adjust the mtdparts to also consider factory-programmed config block. Signed-off-by:
Marek Vasut <marex@denx.de>
-
Marek Vasut authored
- "env ask", "env grep" and "setexpr" are needed for commissioning - add support for ext4 file systems - adjust default environment to use ext4 commands - add write support for (V)FAT and EXT4 - add bitmap and splashscreen support - print timestamp information for images Signed-off-by:
Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
-
- 08 Jul, 2014 2 commits
-
-
git://git.denx.de/u-boot-x86Tom Rini authored
-
Tyler Baker authored
The following patch re-enables the dhcp functionality on omap3_beagle. It was removed with df4dbb5d when omap3_beagle was converted to use ti_omap3_common.h. I have tested beagleboard and beagleboard-xm with this patch and confirmed dhcp is working. Signed-off-by:
Tyler Baker <tyler.baker@linaro.org>
-
- 07 Jul, 2014 4 commits
-
-
Alexey Ignatov authored
Fixes a bug when objcopy doesn't put .dtb.init.rodata section to resulting u-boot.bin, so u-boot was unable to find embedded DTB.
-
Ian Campbell authored
Signed-off-by:
Ian Campbell <ijc@hellion.org.uk> Acked-by:
Hans de Goede <hdegoede@redhat.com>
-
Dirk Eibach authored
sha256 has some beefy memory footprint. Make it optional for constrained systems. Signed-off-by:
Dirk Eibach <dirk.eibach@gdsys.cc>
-
Dirk Eibach authored
Commit "2842c1c2 fit: add sha256 support" badly increased memory footprint, so some of our boards did not build anymore. Since monitor base must not be changed I removed some commands to save memory. Maybe making sha256 optional for fit would be an option for the future since it really has some beefy footprint. Signed-off-by:
Dirk Eibach <dirk.eibach@gdsys.cc>
-