1. 05 Sep, 2018 1 commit
  2. 08 Aug, 2018 1 commit
    • Ye Li's avatar
      MLK-19132-3 fastboot: Remove CONFIG_BCB_SUPPORT for BSP u-boot · 14e87975
      Ye Li authored
      Remove CONFIG_BCB_SUPPORT config from BSP u-boot defconfig files.
      So that we can eliminate such errors during boot up:
      
      can't find partition: misc, dump the partition table
      idx 0, ptn 0 name='gpt' start=0 len=2048
      idx 1, ptn 0 name='tos' start=0 len=2047
      idx 2, ptn 0 name='all' start=0 len=7864320
      idx 3, ptn 0 name='bootloader' start=2 len=4094
      idx 4, ptn 1 name='mmcsdb1' start=20480 len=1024000
      idx 5, ptn 2 name='mmcsdb2' start=1228800 len=6635520
      cannot get the partion info for misc
      Cannot find partition 4080
      do_raw_read failed, ret 1
      read_bootctl, bcb_rw_block read failed
      read command failed
      Signed-off-by: default avatarYe Li <ye.li@nxp.com>
      (cherry picked from commit 4d282a7a429876f1c1c67754a1d5c7aaaf75bb43)
      14e87975
  3. 19 Jul, 2018 1 commit
    • Ye Li's avatar
      MLK-18945-10 imx8mm_evk: Add splash screen support for MIPI DSI · 41f896ce
      Ye Li authored
      Add board level codes for enabling splash screen on imx8mm EVK. We
      support two different display connecting to MIPI DSI miniSAS interfaces:
      
      1. MIPI2HDMI daughter card (default)
      2. RM67191 OLED panel
      
      Users can set "panel" env vairable to "MIPI2HDMI" or "RM67191_OLED" to
      switch them after reboot.
      Signed-off-by: default avatarYe Li <ye.li@nxp.com>
      41f896ce
  4. 06 Jul, 2018 1 commit
  5. 26 Jun, 2018 1 commit
    • Ye Li's avatar
      MLK-18654-4 imx8mm_evk: Enable SPL SDP for iMX8MM EVK board · 619dd4df
      Ye Li authored
      Enable the SPL SDP for iMX8MM EVK. So that when booting from USB serial
      download mode, the SPL will enter SDP to download FIT image from USB host
      (uuu tool) and boot into FIT image.
      
      The SDP driver needs larger malloc pool size, so extend the SPL malloc pool
      to 12KB and reduce the SPL BSS MAX to 4KB because BSS actual size is about 1KB.
      Signed-off-by: default avatarYe Li <ye.li@nxp.com>
      (cherry picked from commit deb9c2bbebc4958ff35157159f68272ce1746143)
      619dd4df
  6. 18 May, 2018 2 commits
  7. 14 May, 2018 1 commit
  8. 11 May, 2018 2 commits
    • Ye Li's avatar
      MLK-18290-5 imx8mm_evk: Add board codes for USB · 62dab684
      Ye Li authored
      Enable the USB host and device support, add relvent board level codes
      and settings.
      
      For device mode, the gadget is fixed on USB device 0. Can't support
      gadget on USB device 1.
      Signed-off-by: default avatarYe Li <ye.li@nxp.com>
      Acked-by: default avatarPeng Fan <peng.fan@nxp.com>
      62dab684
    • Ye Li's avatar
      MLK-18289-2 imx8mm_evk: Add codes to setup typec PD charging · e3579303
      Ye Li authored
      On iMX8MM EVK, the USB2 port is the primary power supply, when USB2 is charging,
      the 3483_EN_SNK1 is not enabled. In the board, we init the tcpc of USB2 first with
      PD enabled. If it is charging, when init the tcpc of USB1 we disable the PD,
      otherwise we enable PD on USB1.
      
      The USB PD switch NX20P3438 needs to exit dead battery mode before
      enable EN_SINK, otherwise the OVP is fixed at 6.8V. Also the OVP threshold needs set to
      23V, when we switch to use 20V VBUS input.
      
      Due to HW issue, after we switched to 9V/20V, set on/off button to off then set back it to
      on, the board can't power up. In this patch we limit the voltage to 5V, will change back
      to 9V/20V when HW fixes the issue.
      Signed-off-by: default avatarYe Li <ye.li@nxp.com>
      Acked-by: default avatarPeng Fan <peng.fan@nxp.com>
      e3579303
  9. 10 May, 2018 1 commit
  10. 24 Feb, 2018 1 commit
  11. 08 Dec, 2017 1 commit
  12. 04 Dec, 2017 1 commit
  13. 02 Nov, 2017 8 commits