sun8i-h2-plus-bananapi-m2-zero.dts 3.14 KB
Newer Older
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
 * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
 *
 * Based on sun8i-h3-bananapi-m2-plus.dts, which is:
 *   Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org>
 */

/dts-v1/;
#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
	model = "Banana Pi BPI-M2-Zero";
	compatible = "sinovoip,bpi-m2-zero", "allwinner,sun8i-h2-plus";

	aliases {
		serial0 = &uart0;
		serial1 = &uart1;
	};

	chosen {
		stdout-path = "serial0:115200n8";
	};

	leds {
		compatible = "gpio-leds";

		pwr_led {
			label = "bananapi-m2-zero:red:pwr";
34
			gpios = <&r_pio 0 10 GPIO_ACTIVE_LOW>; /* PL10 */
35 36 37 38 39 40 41 42 43 44 45 46 47 48
			default-state = "on";
		};
	};

	gpio_keys {
		compatible = "gpio-keys";

		sw4 {
			label = "power";
			linux,code = <BTN_0>;
			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
		};
	};

49 50 51 52 53 54 55 56 57 58 59 60 61
	reg_vdd_cpux: vdd-cpux-regulator {
		compatible = "regulator-gpio";
		regulator-name = "vdd-cpux";
		regulator-type = "voltage";
		regulator-boot-on;
		regulator-always-on;
		regulator-min-microvolt = <1100000>;
		regulator-max-microvolt = <1300000>;
		regulator-ramp-delay = <50>; /* 4ms */

		gpios = <&r_pio 0 1 GPIO_ACTIVE_HIGH>; /* PL1 */
		enable-active-high;
		gpios-states = <0x1>;
62
		states = <1100000 0>, <1300000 1>;
63 64
	};

65 66 67
	wifi_pwrseq: wifi_pwrseq {
		compatible = "mmc-pwrseq-simple";
		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
68 69
		clocks = <&rtc 1>;
		clock-names = "ext_clock";
70 71 72
	};
};

73 74 75 76
&cpu0 {
	cpu-supply = <&reg_vdd_cpux>;
};

77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115
&ehci0 {
	status = "okay";
};

&mmc0 {
	vmmc-supply = <&reg_vcc3v3>;
	bus-width = <4>;
	/*
	 * On the production batch of this board the card detect GPIO is
	 * high active (card inserted), although on the early samples it's
	 * low active.
	 */
	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
	status = "okay";
};

&mmc1 {
	vmmc-supply = <&reg_vcc3v3>;
	vqmmc-supply = <&reg_vcc3v3>;
	mmc-pwrseq = <&wifi_pwrseq>;
	bus-width = <4>;
	non-removable;
	status = "okay";

	brcmf: wifi@1 {
		reg = <1>;
		compatible = "brcm,bcm4329-fmac";
		interrupt-parent = <&pio>;
		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
		interrupt-names = "host-wake";
	};
};

&ohci0 {
	status = "okay";
};

&uart0 {
	pinctrl-names = "default";
116
	pinctrl-0 = <&uart0_pa_pins>;
117 118 119 120 121 122
	status = "okay";
};

&uart1 {
	pinctrl-names = "default";
	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
123
	uart-has-rtscts;
124
	status = "okay";
125 126 127 128 129 130 131 132 133 134 135 136

	bluetooth {
		compatible = "brcm,bcm43438-bt";
		clocks = <&rtc 1>;
		clock-names = "lpo";
		vbat-supply = <&reg_vcc3v3>;
		vddio-supply = <&reg_vcc3v3>;
		device-wakeup-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
		host-wakeup-gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */
		shutdown-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
	};

137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153
};

&usb_otg {
	dr_mode = "otg";
	status = "okay";
};

&usbphy {
	usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
	/*
	 * There're two micro-USB connectors, one is power-only and another is
	 * OTG. The Vbus of these two connectors are connected together, so
	 * the external USB device will be powered just by the power input
	 * from the power-only USB port.
	 */
	status = "okay";
};