Commit 25a7a6f4 authored by Milo Kim's avatar Milo Kim Committed by Lee Jones
Browse files

Documentation: Add LP3943 DT bindings and document



Bindings for LP3943 MFD, GPIO and PWM controller are added.
Signed-off-by: default avatarMilo Kim <milo.kim@ti.com>
Acked-by: default avatarThierry Reding <thierry.reding@gmail.com>
Signed-off-by: default avatarLee Jones <lee.jones@linaro.org>
parent aab5dc68
TI/National Semiconductor LP3943 GPIO controller
Required properties:
- compatible: "ti,lp3943-gpio"
- gpio-controller: Marks the device node as a GPIO controller.
- #gpio-cells: Should be 2. See gpio.txt in this directory for a
description of the cells format.
Example:
Simple LED controls with LP3943 GPIO controller
&i2c4 {
lp3943@60 {
compatible = "ti,lp3943";
reg = <0x60>;
gpioex: gpio {
compatible = "ti,lp3943-gpio";
gpio-controller;
#gpio-cells = <2>;
};
};
};
leds {
compatible = "gpio-leds";
indicator1 {
label = "indi1";
gpios = <&gpioex 9 GPIO_ACTIVE_LOW>;
};
indicator2 {
label = "indi2";
gpios = <&gpioex 10 GPIO_ACTIVE_LOW>;
default-state = "off";
};
};
TI/National Semiconductor LP3943 MFD driver
Required properties:
- compatible: "ti,lp3943"
- reg: I2C slave address. From 0x60 to 0x67.
LP3943 consists of two sub-devices, lp3943-gpio and lp3943-pwm.
For the LP3943 GPIO properties please refer to:
Documentation/devicetree/bindings/gpio/gpio-lp3943.txt
For the LP3943 PWM properties please refer to:
Documentation/devicetree/bindings/pwm/pwm-lp3943.txt
Example:
lp3943@60 {
compatible = "ti,lp3943";
reg = <0x60>;
gpioex: gpio {
compatible = "ti,lp3943-gpio";
gpio-controller;
#gpio-cells = <2>;
};
pwm3943: pwm {
compatible = "ti,lp3943-pwm";
#pwm-cells = <2>;
ti,pwm0 = <8 9 10>;
ti,pwm1 = <15>;
};
};
TI/National Semiconductor LP3943 PWM controller
Required properties:
- compatible: "ti,lp3943-pwm"
- #pwm-cells: Should be 2. See pwm.txt in this directory for a
description of the cells format.
Note that this hardware limits the period length to the
range 6250~1600000.
- ti,pwm0 or ti,pwm1: Output pin number(s) for PWM channel 0 or 1.
0 = output 0
1 = output 1
.
.
15 = output 15
Example:
PWM 0 is for RGB LED brightness control
PWM 1 is for brightness control of LP8557 backlight device
&i2c3 {
lp3943@60 {
compatible = "ti,lp3943";
reg = <0x60>;
/*
* PWM 0 : output 8, 9 and 10
* PWM 1 : output 15
*/
pwm3943: pwm {
compatible = "ti,lp3943-pwm";
#pwm-cells = <2>;
ti,pwm0 = <8 9 10>;
ti,pwm1 = <15>;
};
};
};
/* LEDs control with PWM 0 of LP3943 */
pwmleds {
compatible = "pwm-leds";
rgb {
label = "indi::rgb";
pwms = <&pwm3943 0 10000>;
max-brightness = <255>;
};
};
&i2c4 {
/* Backlight control with PWM 1 of LP3943 */
backlight@2c {
compatible = "ti,lp8557";
reg = <0x2c>;
pwms = <&pwm3943 1 10000>;
pwm-names = "lp8557";
};
};
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment