Commit 5d1ac94d authored by Ye Li's avatar Ye Li
Browse files

MLK-14380-3 mx6ullarm2: Convert to enable OF_CONTROL and DM drivers



Update mx6ull ddr3 arm2 board codes and build configurations
to enable OF_CONTROL and DM drivers.

1. Update QSPI settings and codes for DM QSPI driver.
2. Update GPIO codes for adding gpio request
3. Enable FEC DM driver and update relevant configurations
4. Enable USB DM driver
5. Update PMIC and LDO by-pass codes for DM PMIC
6. Add various boot media support, QSPI/NAND/SPINOR
7. Add rework support for eMMC/QSPIB/TSC
Signed-off-by: default avatarYe Li <ye.li@nxp.com>
parent 2ea5d4b7
......@@ -9,4 +9,13 @@ config SYS_VENDOR
config SYS_CONFIG_NAME
default "mx6ull_ddr3_arm2"
config MX6ULL_DDR3_ARM2_EMMC_REWORK
bool "Select this for the board with eMMC rework"
config MX6ULL_DDR3_ARM2_TSC_REWORK
bool "Select this for the board with screen touch rework"
config MX6ULL_DDR3_ARM2_QSPIB_REWORK
bool "Select this for the board with flash on QSPI-B port rework"
endif
......@@ -21,9 +21,9 @@ IMAGE_VERSION 2
* spi/sd/nand/onenand, qspi/nor
*/
#ifdef CONFIG_SYS_BOOT_QSPI
#ifdef CONFIG_QSPI_BOOT
BOOT_FROM qspi
#elif defined(CONFIG_SYS_BOOT_EIMNOR)
#elif defined(CONFIG_NOR_BOOT)
BOOT_FROM nor
#else
BOOT_FROM sd
......
......@@ -28,7 +28,7 @@
#include <power/pfuze100_pmic.h>
#include "../common/pfuze.h"
#include <usb.h>
#include <usb/ehci-fsl.h>
#include <usb/ehci-ci.h>
#if defined(CONFIG_MXC_EPDC)
#include <lcd.h>
#include <mxc_epdc_fb.h>
......@@ -86,7 +86,7 @@ DECLARE_GLOBAL_DATA_PTR;
#define EPDC_PAD_CTRL 0x010b1
#ifdef CONFIG_SYS_I2C_MXC
#ifdef CONFIG_SYS_I2C
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
/* I2C1 for PMIC and EEPROM */
struct i2c_pads_info i2c_pad_info1 = {
......@@ -160,7 +160,7 @@ static iomux_v3_cfg_t const usdhc1_pads[] = {
};
#endif
#if !defined(CONFIG_SYS_USE_NAND) && !defined(CONFIG_MX6ULL_DDR3_ARM2_QSPIB_REWORK)
#if !defined(CONFIG_CMD_NAND) && !defined(CONFIG_MX6ULL_DDR3_ARM2_QSPIB_REWORK)
static iomux_v3_cfg_t const usdhc2_pads[] = {
/* usdhc2_clk, nand_re_b, qspi1b_clk */
MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
......@@ -194,7 +194,7 @@ static iomux_v3_cfg_t const usdhc2_pads[] = {
};
#endif
#ifdef CONFIG_SYS_USE_NAND
#ifdef CONFIG_CMD_NAND
static iomux_v3_cfg_t const nand_pads[] = {
MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
......@@ -232,7 +232,7 @@ static void setup_gpmi_nand(void)
}
#endif
#ifdef CONFIG_SYS_USE_SPINOR
#ifdef CONFIG_MXC_SPI
static iomux_v3_cfg_t const ecspi1_pads[] = {
MX6_PAD_CSI_DATA06__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX6_PAD_CSI_DATA04__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
......@@ -245,6 +245,7 @@ static iomux_v3_cfg_t const ecspi1_pads[] = {
static void setup_spinor(void)
{
imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
gpio_request(IMX_GPIO_NR(4, 26), "escpi cs");
gpio_direction_output(IMX_GPIO_NR(4, 26), 0);
}
......@@ -315,12 +316,14 @@ static void setup_iomux_fec(int fec_id)
if (fec_id == 0) {
imx_iomux_v3_setup_multiple_pads(fec1_pads,
ARRAY_SIZE(fec1_pads));
gpio_request(IMX_GPIO_NR(5, 2), "fec1 reset");
gpio_direction_output(IMX_GPIO_NR(5, 2), 0);
udelay(50);
gpio_direction_output(IMX_GPIO_NR(5, 2), 1);
} else {
imx_iomux_v3_setup_multiple_pads(fec2_pads,
ARRAY_SIZE(fec2_pads));
gpio_request(IMX_GPIO_NR(5, 4), "fec2 reset");
gpio_direction_output(IMX_GPIO_NR(5, 4), 0);
udelay(50);
gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
......@@ -335,6 +338,7 @@ static void setup_iomux_uart(void)
#ifdef CONFIG_FSL_QSPI
#ifndef CONFIG_DM_SPI
#define QSPI_PAD_CTRL1 \
(PAD_CTL_SRE_FAST | PAD_CTL_SPEED_MED | \
PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_47K_UP | PAD_CTL_DSE_120ohm)
......@@ -358,13 +362,15 @@ static iomux_v3_cfg_t const quadspi_pads[] = {
MX6_PAD_NAND_DATA05__QSPI_B_DATA03 | MUX_PAD_CTRL(QSPI_PAD_CTRL1),
#endif
};
#endif
int board_qspi_init(void)
{
#ifndef CONFIG_DM_SPI
/* Set the iomux */
imx_iomux_v3_setup_multiple_pads(quadspi_pads,
ARRAY_SIZE(quadspi_pads));
#endif
/* Set the clock */
enable_qspi_clk(0);
......@@ -380,7 +386,7 @@ static struct fsl_esdhc_cfg usdhc_cfg[2] = {
#else
{USDHC1_BASE_ADDR, 0, 4},
#endif
#if !defined(CONFIG_SYS_USE_NAND) && !defined(CONFIG_MX6ULL_DDR3_ARM2_QSPIB_REWORK)
#if !defined(CONFIG_CMD_NAND) && !defined(CONFIG_MX6ULL_DDR3_ARM2_QSPIB_REWORK)
{USDHC2_BASE_ADDR, 0, 4},
#endif
};
......@@ -392,11 +398,17 @@ static struct fsl_esdhc_cfg usdhc_cfg[2] = {
int board_mmc_get_env_dev(int devno)
{
if (devno == 1 && mx6_esdhc_fused(USDHC1_BASE_ADDR))
devno = 0;
return devno;
}
int mmc_map_to_kernel_blk(int devno)
{
if (devno == 0 && mx6_esdhc_fused(USDHC1_BASE_ADDR))
devno = 1;
return devno;
}
......@@ -413,7 +425,7 @@ int board_mmc_getcd(struct mmc *mmc)
ret = !gpio_get_value(USDHC1_CD_GPIO);
#endif
break;
#if !defined(CONFIG_SYS_USE_NAND) && !defined(CONFIG_MX6ULL_DDR3_ARM2_QSPIB_REWORK)
#if !defined(CONFIG_CMD_NAND) && !defined(CONFIG_MX6ULL_DDR3_ARM2_QSPIB_REWORK)
case USDHC2_BASE_ADDR:
ret = 1;
break;
......@@ -442,17 +454,21 @@ int board_mmc_init(bd_t *bis)
#else
imx_iomux_v3_setup_multiple_pads(
usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
gpio_request(USDHC1_CD_GPIO, "usdhc1 cd");
gpio_direction_input(USDHC1_CD_GPIO);
#endif
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
/* 3.3V */
gpio_request(USDHC1_VSELECT, "usdhc1 vsel");
gpio_request(USDHC1_PWR_GPIO, "usdhc1 pwr");
gpio_direction_output(USDHC1_VSELECT, 0);
gpio_direction_output(USDHC1_PWR_GPIO, 1);
break;
#if !defined(CONFIG_SYS_USE_NAND) && !defined(CONFIG_MX6ULL_DDR3_ARM2_QSPIB_REWORK)
#if !defined(CONFIG_CMD_NAND) && !defined(CONFIG_MX6ULL_DDR3_ARM2_QSPIB_REWORK)
case 1:
imx_iomux_v3_setup_multiple_pads(
usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
gpio_request(USDHC2_PWR_GPIO, "usdhc2 pwr");
gpio_direction_output(USDHC2_PWR_GPIO, 1);
usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
break;
......@@ -518,11 +534,12 @@ struct lcd_panel_info_t {
void do_enable_parallel_lcd(struct display_info_t const *dev)
{
enable_lcdif_clock(dev->bus);
enable_lcdif_clock(dev->bus, 1);
imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
/* Power up the LCD */
gpio_request(IMX_GPIO_NR(3, 4), "lcd power");
gpio_direction_output(IMX_GPIO_NR(3, 4) , 1);
/* Set Brightness to high */
......@@ -647,6 +664,7 @@ static void setup_epdc_power(void)
/* EPDC_PWRSTAT - GPIO3[16] for PWR_GOOD status */
imx_iomux_v3_setup_pad(MX6_PAD_LCD_DATA11__GPIO3_IO16 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
gpio_request(IMX_GPIO_NR(3, 16), "EPDC_PWRSTAT");
gpio_direction_input(IMX_GPIO_NR(3, 16));
/* EPDC_VCOM0 - GPIO3[24] for VCOM control */
......@@ -654,18 +672,21 @@ static void setup_epdc_power(void)
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(3, 24), "EPDC_VCOM0");
gpio_direction_output(IMX_GPIO_NR(3, 24), 1);
/* EPDC_PWRWAKEUP - GPIO3[14] for EPD PMIC WAKEUP */
imx_iomux_v3_setup_pad(MX6_PAD_LCD_DATA09__GPIO3_IO14 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(3, 14), "EPDC_PWRWAKEUP");
gpio_direction_output(IMX_GPIO_NR(3, 14), 1);
/* EPDC_PWRCTRL0 - GPIO3[17] for EPD PWR CTL0 */
imx_iomux_v3_setup_pad(MX6_PAD_LCD_DATA12__GPIO3_IO17 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(3, 17), "EPDC_PWRCTRL0");
gpio_direction_output(IMX_GPIO_NR(3, 17), 1);
}
......@@ -940,6 +961,105 @@ void ldo_mode_set(int ldo_bypass)
}
}
#endif
#elif defined(CONFIG_DM_PMIC_PFUZE100)
int power_init_board(void)
{
struct udevice *dev;
int ret;
unsigned int reg, dev_id, rev_id;
ret = pmic_get("pfuze100", &dev);
if (ret == -ENODEV)
return ret;
ret = pfuze_mode_init(dev, APS_PFM);
if (ret < 0)
return ret;
dev_id = pmic_reg_read(dev, PFUZE100_DEVICEID);
rev_id = pmic_reg_read(dev, PFUZE100_REVID);
printf("PMIC: PFUZE200! DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
/*
* Our PFUZE0200 is PMPF0200X0AEP, the Pre-programmed OTP
* Configuration is F0.
* Default VOLT:
* VSNVS_VOLT | 3.0V
* SW1AB | 1.375V
* SW2 | 3.3V
* SW3A | 1.5V
* SW3B | 1.5V
* VGEN1 | 1.5V
* VGEN2 | 1.5V
* VGEN3 | 2.5V
* VGEN4 | 1.8V
* VGEN5 | 2.8V
* VGEN6 | 3.3V
*
* According to schematic, we need SW3A 1.35V, SW3B 3.3V,
* VGEN1 1.2V, VGEN2 1.5V, VGEN3 2.8V, VGEN4 1.8V,
* VGEN5 3.3V, VGEN6 3.0V.
*
* Here we just use the default VOLT, but not configure
* them, when needed, configure them to our requested voltage.
*/
/* Set SW1AB stanby volage to 0.975V */
reg = pmic_reg_read(dev, PFUZE100_SW1ABSTBY);
reg &= ~SW1x_STBY_MASK;
reg |= SW1x_0_975V;
pmic_reg_write(dev, PFUZE100_SW1ABSTBY, reg);
/* Set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
reg = pmic_reg_read(dev, PFUZE100_SW1ABCONF);
reg &= ~SW1xCONF_DVSSPEED_MASK;
reg |= SW1xCONF_DVSSPEED_4US;
pmic_reg_write(dev, PFUZE100_SW1ABCONF, reg);
/* Enable power of VGEN5 3V3 */
reg = pmic_reg_read(dev, PFUZE100_VGEN5VOL);
reg &= ~0x1F;
reg |= 0x1F;
pmic_reg_write(dev, PFUZE100_VGEN5VOL, reg);
return 0;
}
#ifdef CONFIG_LDO_BYPASS_CHECK
void ldo_mode_set(int ldo_bypass)
{
struct udevice *dev;
int ret;
int is_400M;
u32 vddarm;
ret = pmic_get("pfuze100", &dev);
if (ret == -ENODEV) {
printf("No PMIC found!\n");
return;
}
/* switch to ldo_bypass mode */
if (ldo_bypass) {
/* decrease VDDARM to 1.275V */
pmic_clrsetbits(dev, PFUZE100_SW1ABVOL, 0x3f, PFUZE100_SW1ABC_SETP(12750));
is_400M = set_anatop_bypass(1);
if (is_400M)
vddarm = PFUZE100_SW1ABC_SETP(10750);
else
vddarm = PFUZE100_SW1ABC_SETP(11750);
pmic_clrsetbits(dev, PFUZE100_SW1ABVOL, 0x3f, vddarm);
set_anatop_bypass(1);
printf("switch to ldo_bypass mode!\n");
}
}
#endif
#endif
int board_early_init_f(void)
......@@ -954,7 +1074,7 @@ int board_init(void)
/* Address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_SYS_I2C_MXC
#ifdef CONFIG_SYS_I2C
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
#endif
......@@ -962,15 +1082,15 @@ int board_init(void)
setup_fec(CONFIG_FEC_ENET_DEV);
#endif
#ifdef CONFIG_SYS_USE_SPINOR
#ifdef CONFIG_MXC_SPI
setup_spinor();
#endif
#ifdef CONFIG_SYS_USE_NAND
#ifdef CONFIG_CMD_NAND
setup_gpmi_nand();
#endif
#ifdef CONFIG_SYS_USE_QSPI
#ifdef CONFIG_FSL_QSPI
board_qspi_init();
#endif
......
......@@ -2,4 +2,51 @@ CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.c
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_MX6ULL_DDR3_ARM2=y
CONFIG_CMD_GPIO=y
\ No newline at end of file
CONFIG_VIDEO=y
CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-ddr3-arm2"
CONFIG_DEFAULT_FDT_FILE="imx6ull-14x14-ddr3-arm2.dtb"
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MMC=y
CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
CONFIG_CMD_I2C=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_NET=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
# CONFIG_BLK is not set
CONFIG_DM_GPIO=y
CONFIG_DM_I2C=y
CONFIG_DM_MMC=y
CONFIG_DM_SPI=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_DM_MMC_OPS is not set
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_PFUZE100=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_FSL_QSPI=y
CONFIG_DM_ETH=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg,MX6ULL_DDR3_ARM2_EMMC_REWORK"
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg"
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_MX6ULL_DDR3_ARM2=y
CONFIG_CMD_GPIO=y
\ No newline at end of file
CONFIG_VIDEO=y
CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-ddr3-arm2-emmc"
CONFIG_DEFAULT_FDT_FILE="imx6ull-14x14-ddr3-arm2.dtb"
CONFIG_MX6ULL_DDR3_ARM2_EMMC_REWORK=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
CONFIG_CMD_I2C=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_NET=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
# CONFIG_BLK is not set
CONFIG_DM_GPIO=y
CONFIG_DM_I2C=y
CONFIG_DM_MMC=y
# CONFIG_DM_MMC_OPS is not set
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_PFUZE100=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_ETH=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg,MXC_EPDC"
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg"
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_MX6ULL_DDR3_ARM2=y
CONFIG_VIDEO=y
CONFIG_MXC_EPDC=y
CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-ddr3-arm2-epdc"
CONFIG_DEFAULT_FDT_FILE="imx6ull-14x14-ddr3-arm2.dtb"
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MMC=y
CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
CONFIG_CMD_I2C=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_NET=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
# CONFIG_BLK is not set
CONFIG_DM_GPIO=y
CONFIG_DM_I2C=y
CONFIG_DM_MMC=y
CONFIG_DM_SPI=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_DM_MMC_OPS is not set
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_PFUZE100=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_FSL_QSPI=y
CONFIG_DM_ETH=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg,SYS_BOOT_NAND"
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg"
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_MX6ULL_DDR3_ARM2=y
CONFIG_CMD_GPIO=y
\ No newline at end of file
CONFIG_VIDEO=y
CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-ddr3-arm2-gpmi-weim"
CONFIG_DEFAULT_FDT_FILE="imx6ull-14x14-ddr3-arm2.dtb"
CONFIG_NAND_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
CONFIG_CMD_I2C=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_NET=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
# CONFIG_BLK is not set
CONFIG_DM_GPIO=y
CONFIG_DM_I2C=y
CONFIG_DM_MMC=y
# CONFIG_DM_MMC_OPS is not set
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_PFUZE100=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_DM_ETH=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg"
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_MX6ULL_DDR3_ARM2=y
CONFIG_VIDEO=y
CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-ddr3-arm2"
CONFIG_DEFAULT_FDT_FILE="imx6ull-14x14-ddr3-arm2.dtb"
CONFIG_USE_IMXIMG_PLUGIN=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_IMLS is not set
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_MMC=y
CONFIG_CMD_SF=y
CONFIG_CMD_USB=y
CONFIG_CMD_I2C=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_NET=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_EXT4_WRITE=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_OF_CONTROL=y
# CONFIG_BLK is not set
CONFIG_DM_GPIO=y
CONFIG_DM_I2C=y
CONFIG_DM_MMC=y
CONFIG_DM_SPI=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_DM_MMC_OPS is not set
CONFIG_PINCTRL=y
CONFIG_PINCTRL_IMX6=y
CONFIG_DM_PMIC=y
CONFIG_DM_PMIC_PFUZE100=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_PFUZE100=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_USB=y
CONFIG_DM_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_FSL_QSPI=y
CONFIG_DM_ETH=y
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg,SYS_BOOT_QSPI"
CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=board/freescale/mx6ull_ddr3_arm2/imximage.cfg"
CONFIG_ARM=y
CONFIG_ARCH_MX6=y
CONFIG_TARGET_MX6ULL_DDR3_ARM2=y
CONFIG_CMD_GPIO=y
\ No newline at end of file
CONFIG_VIDEO=y
CONFIG_DEFAULT_DEVICE_TREE="imx6ull-14x14-ddr3-arm2"
CONFIG_DEFAULT_FDT_FILE="imx6ull-14x14-ddr3-arm2.dtb"
CONFIG_QSPI_BOOT=y
CONFIG_BOOTDELAY=3
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
CONFIG_CMD_BOOTZ=y