Add a VID:PID for the BroadModi BM818 M.2 card

Co-developed-by:  <bob.ham@puri.sm>
Signed-off-by:  <bob.ham@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

Without a VBUS supply the dwc3 driver won't go into otg mode.

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

Due to current spikes during boot the USB-C VBUS can get drawn down too
low causing the bq25890 to reset the board. Allow VBUS to drop a bit
further to make allowance for thses spikes.

Signed-off-by: Eric Kuzmenko <eric.kuzmenko@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

The bq25890 has low voltage protection on VIN. Allow the register
to be set from the device tree.

Signed-off-by: Eric Kuzmenko <eric.kuzmenko@puri.sm>
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

This uses

 - our nwl mipi dsi controller driver
 - our mixel dphy driver
 - a forward port from NXPs dcss driver from our 4.18 tree
   (which we got from their 4.9/4.14 trees)
 - a forward port NXPs patches to the imx-display-subsystem driver
   from our 4.18 tree (which we got from their 4.9/4.14 trees)

ctxld fails during boot due to its irqsteer dependency. Make us undo
less stuff so that probing again works later on (instead of hanging the
boot).

TODO: check if this works on 4.18 too

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

We're returning != 0 on error

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

See 463659a0



Signed-off-by: Guido Günther <guido.gunther@puri.sm>

According to 4.18 we have B0. Need to check what to do about busfreq

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Like in 1ef2917d



Signed-off-by: Guido Günther <guido.gunther@puri.sm>

like in f53705fd



Signed-off-by: Guido Günther <guido.gunther@puri.sm>

We don't have anything feeding these and they cause trouble when
rebasing on linux-next so drop them.

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

from NXPs kernel

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

We don't need it atm.

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

This is just a hack until we have a proper solution. We don't want
to allow userspace patch all kernel space.

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

0x14000 and 0x14018 are SRC_ADDR and DEST_ADDR in the BLT engine.
0x15C00 are the TX_DESCRIPTOR addresses on Halti5 at least.

This avoids the etnaviv_warn_if_non_sensitive warnings.

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Otherwise we might end up with modules that can't be loaded:

  modprobe: ERROR: could not insert 'goodix': Unknown symbol in module, or unknown parameter (see dmesg)
  [   15.190397] goodix: Unknown symbol touchscreen_report_pos (err -2)
  [   15.221560] goodix: Unknown symbol touchscreen_parse_properties (err -2)
  [   64.677545] goodix: Unknown symbol touchscreen_report_pos (err -2)
  [   64.683767] goodix: Unknown symbol touchscreen_parse_properties (err -2)

Signed-off-by: Guido Günther <agx@sigxcpu.org>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

The mainline ATF doesn't currently support the FSL_SIP_GET_SOC_INFO call
nor does it have the code to identify different imx8mq SOC revisions so
mimic what NXPs ATF does here.

As a fallback use ATF so we can identify new revisions once it gains
support or when using NXPs ATF.

Signed-off-by: Guido Günther <agx@sigxcpu.org>

This adds initial support for the NWL MIPI DSI Host controller found on
i.MX8 SoCs.

It adds support for the i.MX8MQ but the same IP can be found on
i.MX8QXP.

It has been tested on the Librem 5 devkit using DCSS.

Co-developed-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Guido Günther <agx@sigxcpu.org>

The Northwest Logic MIPI DSI IP core can be found in NXPs i.MX8
Socs.

Signed-off-by: Guido Günther <agx@sigxcpu.org>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

Signed-off-by: Guido Günther <guido.gunther@puri.sm>

During the i2c probe the clock must be active

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

Need to be able to enable the camera so use a named gpio-led
instead of an unnamed gpio.

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

Enable sound support for the devkit including the modem

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

Connect the WoWWAN signal to a gpio key to wake the system

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

Use the 3v3 peripheral regulator instead of the pwr_en one

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>

Specify all of the mclk's for the sai interfaces.

Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>