Select Git revision
Search by author
- Any Author
- authors
-
Angus Ainslie
angus.ainslie
-
Eric Kuzmenko
eric.kuzmenko
-
Evangelos Ribeiro Tzaras
evangelos.tzaras
-
Francois Techene
francois.techene
-
Guido Gunther
guido.gunther
-
JC Staudt
jcstaudt
-
Jonathon Hall
jonathon.hall
-
Julian Sparber
julian.sparber
-
Martin Kepplinger
martin.kepplinger
-
Mohammed Sadiq
mohammed.sadiq
-
Richard Kolla
richard.kolla
-
Sam Hewitt sam.hewitt
-
Sebastian Krzyszkowiak
sebastian.krzyszkowiak
- Aug 31, 2018
-
-
Hans Verkuil authored
Integrate the request support. This adds the v4l2_ctrl_request_complete and v4l2_ctrl_request_setup functions to complete a request and (as a helper function) to apply a request to the hardware. It takes care of queuing requests and correctly chaining control values in the request queue. Note that when a request is marked completed it will copy control values to the internal request state. This can be optimized in the future since this is sub-optimal when dealing with large compound and/or array controls. For the initial 'stateless codec' use-case the current implementation is sufficient. Signed-off-by:
-
Hans Verkuil authored
The next patch needs the reference to a control instead of the control itself, so change struct v4l2_ctrl_helper accordingly. Signed-off-by:
-
Hans Verkuil authored
To store request data the handler_new_ref() allocates memory for it if needed. Signed-off-by:
-
Hans Verkuil authored
Embed and initialize a media_request_object in struct v4l2_ctrl_handler. Add a p_req field to struct v4l2_ctrl_ref that will store the request value. Signed-off-by:
-
Hans Verkuil authored
Add a 'bool from_other_dev' argument: set to true if the two handlers refer to different devices (e.g. it is true when inheriting controls from a subdev into a main v4l2 bridge driver). This will be used later when implementing support for the request API since we need to skip such controls. Signed-off-by:
-
Alexandre Courbot authored
If 'which' is V4L2_CTRL_WHICH_REQUEST_VAL, then the 'request_fd' field can be used to specify a request for the G/S/TRY_EXT_CTRLS ioctls. Signed-off-by:
-
Hans Verkuil authored
We need to serialize streamon/off with queueing new requests. These ioctls may trigger the cancellation of a streaming operation, and that should not be mixed with queuing a new request at the same time. Finally close() needs this lock since that too can trigger the cancellation of a streaming operation. We take the req_queue_mutex here before any other locks since it is a very high-level lock. Signed-off-by:
-
Hans Verkuil authored
Add a simple helper function that tests if the driver supports the request API. Signed-off-by:
-
Hans Verkuil authored
Add media_request_object_find to find a request object inside a request based on ops and priv values. Objects of the same type (vb2 buffer, control handler) will have the same ops value. And objects that refer to the same 'parent' object (e.g. the v4l2_ctrl_handler that has the current driver state) will have the same priv value. The caller has to call media_request_object_put() for the returned object since this function increments the refcount. Signed-off-by:
-
Hans Verkuil authored
Add media_request_get_by_fd() to find a request based on the file descriptor. The caller has to call media_request_put() for the returned request since this function increments the refcount. Signed-off-by:
-
Sakari Ailus authored
media-request.h has been recently added; add it to the documentation build as well. Signed-off-by:
-
Hans Verkuil authored
Add initial media request support: 1) Add MEDIA_IOC_REQUEST_ALLOC ioctl support to media-device.c 2) Add struct media_request to store request objects. 3) Add struct media_request_object to represent a request object. 4) Add MEDIA_REQUEST_IOC_QUEUE/REINIT ioctl support. Basic lifecycle: the application allocates a request, adds objects to it, queues the request, polls until it is completed and can then read the final values of the objects at the time of completion. When it closes the file descriptor the request memory will be freed (actually, when the last user of that request releases the request). Drivers will bind an object to a request (the 'adds objects to it' phase), when MEDIA_REQUEST_IOC_QUEUE is called the request is validated (req_validate op), then queued (the req_queue op). When done with an object it can either be unbound from the request (e.g. when the driver has finished with a vb2 buffer) or marked as completed (e.g. for controls associated with a buffer). When all objects in the request are completed (or unbound), then the request fd will signal an exception (poll). Co-developed-by:
-
Hans Verkuil authored
Define the public request API. This adds the new MEDIA_IOC_REQUEST_ALLOC ioctl to allocate a request and two ioctls that operate on a request in order to queue the contents of the request to the driver and to re-initialize the request. Signed-off-by:
-
Alexandre Courbot authored
Document the request API for V4L2 devices, and amend the documentation of system calls influenced by it. Signed-off-by:
-
Hans Verkuil authored
The pixelclock detection of the adv7842 is precise enough to detect if the framerate is 60 Hz or 59.94 Hz (aka "reduced fps"). Implement this detection. Signed-off-by:
-
Jose Abreu authored
Currently, cobalt driver always returns 60fps in g_parm. This patch uses the new v4l2_calc_timeperframe helper to calculate the time per frame value. Signed-off-by:
-
Jose Abreu authored
A new helper function was introduced to facilitate the calculation of time per frame value whenever we have access to the full v4l2_dv_timings structure. This should be used only for receivers and only when there is enough accuracy in the measured pixel clock value as well as in the horizontal/vertical values. Signed-off-by:
-
Jose Abreu authored
Add a new flag to UAPI for DV timings which, whenever set, indicates that hardware can detect the difference between regular FPS and 1000/1001 FPS. This is specific to HDMI receivers. Also, it is only valid when V4L2_DV_FL_CAN_REDUCE_FPS is set. Signed-off-by:
-
Hans Verkuil authored
Document the new V4L2_DV_FL_CAN_DETECT_REDUCED_FPS flag and update the V4L2_DV_FL_REDUCED_FPS description since it can now also be used with receivers. Signed-off-by:
-
Hugues Fruchet authored
fixes: 6949d864 ("media: ov5640: do not change mode if format or frame interval is unchanged"). Symptom was fuzzy image because of JPEG default format not being changed according to new format selected, fix this. Init sequence initialises format to YUV422 UYVY but sensor->fmt initial value was set to JPEG, fix this. Signed-off-by:
-
Alexey Khoroshilov authored
If ov772x_power_on() is unable to get GPIO rstb, the clock is left undisabled. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
-
zhong jiang authored
dma_zalloc_coherent has implemented the dma_alloc_coherent() + memset(), We prefer to dma_zalloc_coherent instead of open-codeing. Signed-off-by:
-
Sakari Ailus authored
pm_runtime_get_if_in_use() returns -EINVAL if runtime PM is disabled. This should not be considered an error. Generally the driver has enabled runtime PM already so getting this error due to runtime PM being disabled will not happen. Instead of checking for lesser or equal to zero, check for zero only. Address this for drivers where this pattern exists. This patch has been produced using the following command: $ git grep -l pm_runtime_get_if_in_use -- drivers/media/i2c/ | \ xargs perl -i -pe 's/(pm_runtime_get_if_in_use\(.*\)) \<\= 0/!$1/' Signed-off-by:
-
Sakari Ailus authored
Replace the calls to pm_runtime_get_noresume() and pm_runtime_put() with pm_runtime_idle() in the driver's probe function. This will have the same effect with fewer calls. pm_runtime_disable() in remove is sufficient as the device is already in RPM_SUSPENDED state. Signed-off-by:
-
Akinobu Mita authored
Convert ov965x register access to use SCCB regmap. Cc: Mark Brown <broonie@kernel.org> Cc: Peter Rosin <peda@axentia.se> Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Jacopo Mondi <jacopo+renesas@jmondi.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Akinobu Mita authored
Convert ov772x register access to use SCCB regmap. Cc: Mark Brown <broonie@kernel.org> Cc: Peter Rosin <peda@axentia.se> Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Jacopo Mondi <jacopo+renesas@jmondi.org> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Hans Verkuil authored
While decoding you need to make sure you do not get values < 0 or > 255. Note that since this code will also be used in userspace utilities the clamp macro isn't used since that is kernel-only. Signed-off-by:
-
Hans Verkuil authored
Split off the decode and encode functions into a separate source that can be reused elsewhere. Signed-off-by:
-
Hans Verkuil authored
The codec source is generic and not vicodec specific. It can be used by other drivers or userspace as well. So rename the source and header to something more generic (codec-fwht.c/h) and prefix the defines, types and functions with fwht_. Signed-off-by:
-
Hans Verkuil authored
Exit the loop immediately once it is clear that the plane cannot be compressed. Also clear the PCODED bit and fix the PCODED check (it should check for the bit) in the caller code. Signed-off-by:
-
Hans Verkuil authored
Simplify some blocktype/is_intra checks. Signed-off-by:
-
Hans Verkuil authored
The flags field can be removed from struct vicodec_q_data. This simplifies the flags handling elsewhere. Signed-off-by:
-
Hans Verkuil authored
Add support for 4:2:2, 4:4:4 and RGB 24/32 bits formats. This makes it a lot more useful, esp. as a simple video compression codec for use with v4l2-ctl/qvidcap. Note that it does not do any conversion between e.g. 4:2:2 and 4:2:0 or RGB and YUV: it still just compresses planes be they Y/U/V or R/G/B. Signed-off-by:
-
Hans Verkuil authored
Instead of hardcoding the quantization parameter (or 'DEADZONE_WIDTH' as it was called in the codec) make this configurable through two controls: one for I frames, one for P frames. Also allow changing these parameters and the GOP_SIZE parameter while streaming. Signed-off-by:
-
- Aug 29, 2018
-
-
Arnd Bergmann authored
Multiple files in this driver fail to build because of missing header inclusions: drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c: In function 'csiphy_hw_version_read': drivers/media/platform/qcom/camss/camss-csiphy-2ph-1-0.c:31:18: error: implicit declaration of function 'readl_relaxed'; did you mean 'xchg_relaxed'? [-Werror=implicit-function-declaration] drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c: In function 'csiphy_hw_version_read': drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c:52:2: error: implicit declaration of function 'writel' [-Werror=implicit-function-declaration] Add linux/io.h there and in all other files that call readl/writel and related interfaces. Signed-off-by:
-
Todor Tomov authored
Use managed memory allocations for structs which are used until the driver is removed. Signed-off-by:
-
Arnd Bergmann authored
The empty suspend/resume functions cause a build warning when they are unused: drivers/media/platform/qcom/camss/camss.c:1001:12: error: 'camss_runtime_resume' defined but not used [-Werror=unused-function] drivers/media/platform/qcom/camss/camss.c:996:12: error: 'camss_runtime_suspend' defined but not used [-Werror=unused-function] Mark them as __maybe_unused so the compiler can silently drop them. Fixes: 02afa816 ("media: camss: Add basic runtime PM support") Signed-off-by:
-
Jozef Balga authored
When less than 3 bytes are written to the device, memcpy is called with negative array size which leads to buffer overflow and kernel panic. This patch adds a condition and returns -EOPNOTSUPP instead. Fixes bugzilla issue 64871 [mchehab+samsung@kernel.org: fix a merge conflict and changed the condition to match the patch's comment, e. g. len == 3 could also be valid] Signed-off-by:
-
Hans Verkuil authored
This fixes this warning: Documentation/media/uapi/dvb/video_function_calls.rst:9: WARNING: toctree contains reference to nonexisting document 'uapi/dvb/video-set-attributes' Signed-off-by:
-
- Aug 26, 2018
-
-
Linus Torvalds authored
-