- Dec 08, 2021
-
-
Jay Dolan authored
commit bb1201d4 upstream. Have pericom_do_set_divisor() use the uartclk instead of a hard coded value to work with different speed crystals. Tested with 14.7456 and 24 MHz crystals. Have pericom_do_set_divisor() always calculate the divisor rather than call serial8250_do_set_divisor() for rates below baud_base. Do not write registers or call serial8250_do_set_divisor() if valid divisors could not be found. Fixes: 6bf4e42f ("serial: 8250: Add support for higher baud rates to Pericom chips") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Jay Dolan <jay.dolan@accesio.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jay Dolan authored
commit c525c5d2 upstream. Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port. Fixes: 78d3820b ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Jay Dolan <jay.dolan@accesio.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
commit 00de977f upstream. Commit 761ed4a9 ("tty: serial_core: convert uart_close to use tty_port_close") converted serial core to use tty_port_close() but failed to notice that the transmit buffer still needs to be freed on final close. Not freeing the transmit buffer means that the buffer is no longer cleared on next open so that any ioctl() waiting for the buffer to drain might wait indefinitely (e.g. on termios changes) or that stale data can end up being transmitted in case tx is restarted. Furthermore, the buffer of any port that has been opened would leak on driver unbind. Note that the port lock is held when clearing the buffer pointer due to the ldisc race worked around by commit a5ba1d95 ("uart: fix race between uart_put_char() and uart_shutdown()"). Also note that the tty-port shutdown() callback is not called for console ports so it is not strictly necessary to free the buffer page after releasing the lock (cf. d7240214 ("tty/serial: do not free trasnmit buffer page under port lock")). Link: https://lore.kernel.org/r/319321886d97c456203d5c6a576a5480d07c3478.1635781688.git.baruch@tkos.co.il Fixes: 761ed4a9 ("tty: serial_core: convert uart_close to use tty_port_close") Cc: stable@vger.kernel.org # 4.9 Cc: Rob Herring <robh@kernel.org> Reported-by:
Baruch Siach <baruch@tkos.co.il> Tested-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211108085431.12637-1-johan@kernel.org Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Patrik John authored
commit b40de746 upstream. The current implementation uses 0 as lower limit for the baud rate tolerance for tegra20 and tegra30 chips which causes isses on UART initialization as soon as baud rate clock is lower than required even when within the standard UART tolerance of +/- 4%. This fix aligns the implementation with the initial commit description of +/- 4% tolerance for tegra chips other than tegra186 and tegra194. Fixes: d781ec21 ("serial: tegra: report clk rate errors") Cc: stable <stable@vger.kernel.org> Signed-off-by:
Patrik John <patrik.john@u-blox.com> Link: https://lore.kernel.org/r/sig.19614244f8.20211123132737.88341-1-patrik.john@u-blox.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Pierre Gondois authored
commit ac442a07 upstream. The document 'ACPI for Arm Components 1.0' defines the following _HID mappings: -'Prime cell UART (PL011)': ARMH0011 -'SBSA UART': ARMHB000 Use the sbsa-uart driver when a device is described with the 'ARMHB000' _HID. Note: PL011 devices currently use the sbsa-uart driver instead of the uart-pl011 driver. Indeed, PL011 devices are not bound to a clock in ACPI. It is not possible to change their baudrate. Cc: <stable@vger.kernel.org> Signed-off-by:
Pierre Gondois <Pierre.Gondois@arm.com> Link: https://lore.kernel.org/r/20211109172248.19061-1-Pierre.Gondois@arm.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Sven Eckelmann authored
commit 7492ffc9 upstream. The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of setup, it is often sharing a serial device with the normal system console. This is usually no problem because the polling helpers can consume input values directly (when in kgdb context) and the normal Linux handlers can only consume new input values after kgdb switched back. This is not true anymore when RX DMA is enabled for UARTDM controllers. Single input values can no longer be received correctly. Instead following seems to happen: * on 1. input, some old input is read (continuously) * on 2. input, two old inputs are read (continuously) * on 3. input, three old input values are read (continuously) * on 4. input, 4 previous inputs are received This repeats then for each group of 4 input values. This behavior changes slightly depending on what state the controller was when the first input was received. But this makes working with kgdb basically impossible because control messages are always corrupted when kgdboc tries to parse them. RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid these kind of problems. No such problem was noticed for TX DMA. Fixes: 99693945 ("tty: serial: msm: Add RX DMA support") Cc: stable@vger.kernel.org Signed-off-by:
Sven Eckelmann <sven@narfation.org> Link: https://lore.kernel.org/r/20211113121050.7266-1-sven@narfation.org Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Joerg Roedel authored
commit 51523ed1 upstream. The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff range of kernel memory (with 4-level paging). This range contains the kernel's text+data+bss mappings and the module mapping space but not the direct mapping and the vmalloc area. This is enough to get the application processors out of real-mode, but for code that switches back to real-mode the trampoline_pgd is missing important parts of the address space. For example, consider this code from arch/x86/kernel/reboot.c, function machine_real_restart() for a 64-bit kernel: #ifdef CONFIG_X86_32 load_cr3(initial_page_table); #else write_cr3(real_mode_header->trampoline_pgd); /* Exiting long mode will fail if CR4.PCIDE is set. */ if (boot_cpu_has(X86_FEATURE_PCID)) cr4_clear_bits(X86_CR4_PCIDE); #endif /* Jump to the identity-mapped low memory code */ #ifdef CONFIG_X86_32 asm volatile("jmpl *%0" : : "rm" (real_mode_header->machine_real_restart_asm), "a" (type)); #else asm volatile("ljmpl *%0" : : "m" (real_mode_header->machine_real_restart_asm), "D" (type)); #endif The code switches to the trampoline_pgd, which unmaps the direct mapping and also the kernel stack. The call to cr4_clear_bits() will find no stack and crash the machine. The real_mode_header pointer below points into the direct mapping, and dereferencing it also causes a crash. The reason this does not crash always is only that kernel mappings are global and the CR3 switch does not flush those mappings. But if theses mappings are not in the TLB already, the above code will crash before it can jump to the real-mode stub. Extend the trampoline_pgd to contain all kernel mappings to prevent these crashes and to make code which runs on this page-table more robust. Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20211202153226.22946-5-joro@8bytes.org Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Feng Tang authored
commit b50db709 upstream. There are cases that the TSC clocksource is wrongly judged as unstable by the clocksource watchdog mechanism which tries to validate the TSC against HPET, PM_TIMER or jiffies. While there is hardly a general reliable way to check the validity of a watchdog, Thomas Gleixner proposed [1]: "I'm inclined to lift that requirement when the CPU has: 1) X86_FEATURE_CONSTANT_TSC 2) X86_FEATURE_NONSTOP_TSC 3) X86_FEATURE_NONSTOP_TSC_S3 4) X86_FEATURE_TSC_ADJUST 5) At max. 4 sockets After two decades of horrors we're finally at a point where TSC seems to be halfway reliable and less abused by BIOS tinkerers. TSC_ADJUST was really key as we can now detect even small modifications reliably and the important point is that we can cure them as well (not pretty but better than all other options)." As feature #3 X86_FEATURE_NONSTOP_TSC_S3 only exists on several generations of Atom processorz, and is always coupled with X86_FEATURE_CONSTANT_TSC and X86_FEATURE_NONSTOP_TSC, skip checking it, and also be more defensive to use maximal 2 sockets. The check is done inside tsc_init() before registering 'tsc-early' and 'tsc' clocksources, as there were cases that both of them had been wrongly judged as unreliable. For more background of tsc/watchdog, there is a good summary in [2] [tglx} Update vs. jiffies: On systems where the only remaining clocksource aside of TSC is jiffies there is no way to make this work because that creates a circular dependency. Jiffies accuracy depends on not missing a periodic timer interrupt, which is not guaranteed. That could be detected by TSC, but as TSC is not trusted this cannot be compensated. The consequence is a circulus vitiosus which results in shutting down TSC and falling back to the jiffies clocksource which is even more unreliable. [1]. https://lore.kernel.org/lkml/87eekfk8bd.fsf@nanos.tec.linutronix.de/ [2]. https://lore.kernel.org/lkml/87a6pimt1f.ffs@nanos.tec.linutronix.de/ [ tglx: Refine comment and amend changelog ] Fixes: 6e3cd952 ("x86/hpet: Use another crystalball to evaluate HPET usability") Suggested-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Feng Tang <feng.tang@intel.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211117023751.24190-2-feng.tang@intel.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Feng Tang authored
commit c7719e79 upstream. The TSC_ADJUST register is checked every time a CPU enters idle state, but Thomas Gleixner mentioned there is still a caveat that a system won't enter idle [1], either because it's too busy or configured purposely to not enter idle. Setup a periodic timer (every 10 minutes) to make sure the check is happening on a regular base. [1] https://lore.kernel.org/lkml/875z286xtk.fsf@nanos.tec.linutronix.de/ Fixes: 6e3cd952 ("x86/hpet: Use another crystalball to evaluate HPET usability") Requested-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Feng Tang <feng.tang@intel.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211117023751.24190-1-feng.tang@intel.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Zhou Qingyang authored
commit 37307f70 upstream. In cdnsp_endpoint_init(), cdnsp_ring_alloc() is assigned to pep->ring and there is a dereference of it in cdnsp_endpoint_init(), which could lead to a NULL pointer dereference on failure of cdnsp_ring_alloc(). Fix this bug by adding a check of pep->ring. This bug was found by a static analyzer. The analysis employs differential checking to identify inconsistent security operations (e.g., checks or kfrees) between two code paths and confirms that the inconsistent operations are not recovered in the current function or the callers, so they constitute bugs. Note that, as a bug found by static analysis, it can be a false positive or hard to trigger. Multiple researchers have cross-reviewed the bug. Builds with CONFIG_USB_CDNSP_GADGET=y show no new warnings, and our static analyzer no longer warns about this code. Fixes: 3d829045 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") Cc: stable <stable@vger.kernel.org> Acked-by:
Pawel Laszczak <pawell@cadence.com> Acked-by:
Peter Chen <peter.chen@kernel.org> Signed-off-by:
Zhou Qingyang <zhou1615@umn.edu> Link: https://lore.kernel.org/r/20211130172700.206650-1-zhou1615@umn.edu Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Frank Li authored
commit 387c2b6b upstream. This issue was found at android12 MTP. 1. MTP submit many out urb request. 2. Cancel left requests (>20) when enough data get from host 3. Send ACK by IN endpoint. 4. MTP submit new out urb request. 5. 4's urb never complete. TRACE LOG: MtpServer-2157 [000] d..3 1287.150391: cdns3_ep_dequeue: ep1out: req: 00000000299e6836, req buff 000000009df42287, length: 0/16384 zsi, status: -115, trb: [start:87, end:87: virt addr 0x80004000ffd50420], flags:1 SID: 0 MtpServer-2157 [000] d..3 1287.150410: cdns3_gadget_giveback: ep1out: req: 00000000299e6836, req buff 000000009df42287, length: 0/16384 zsi, status: -104, trb: [start:87, end:87: virt addr 0x80004000ffd50420], flags:0 SID: 0 MtpServer-2157 [000] d..3 1287.150433: cdns3_ep_dequeue: ep1out: req: 0000000080b7bde6, req buff 000000009ed5c556, length: 0/16384 zsi, status: -115, trb: [start:88, end:88: virt addr 0x80004000ffd5042c], flags:1 SID: 0 MtpServer-2157 [000] d..3 1287.150446: cdns3_gadget_giveback: ep1out: req: 0000000080b7bde6, req buff 000000009ed5c556, length: 0/16384 zsi, status: -104, trb: [start:88, end:88: virt addr 0x80004000ffd5042c], flags:0 SID: 0 .... MtpServer-2157 [000] d..1 1293.630410: cdns3_alloc_request: ep1out: req: 00000000afbccb7d, req buff 0000000000000000, length: 0/0 zsi, status: 0, trb: [start:0, end:0: virt addr (null)], flags:0 SID: 0 MtpServer-2157 [000] d..2 1293.630421: cdns3_ep_queue: ep1out: req: 00000000afbccb7d, req buff 00000000871caf90, length: 0/512 zsi, status: -115, trb: [start:0, end:0: virt addr (null)], flags:0 SID: 0 MtpServer-2157 [000] d..2 1293.630445: cdns3_wa1: WA1: ep1out set guard MtpServer-2157 [000] d..2 1293.630450: cdns3_wa1: WA1: ep1out restore cycle bit MtpServer-2157 [000] d..2 1293.630453: cdns3_prepare_trb: ep1out: trb 000000007317b3ee, dma buf: 0xffd5bc00, size: 512, burst: 128 ctrl: 0x00000424 (C=0, T=0, ISP, IOC, Normal) SID:0 LAST_SID:0 MtpServer-2157 [000] d..2 1293.630460: cdns3_doorbell_epx: ep1out, ep_trbaddr ffd50414 .... irq/241-5b13000-2154 [000] d..1 1293.680849: cdns3_epx_irq: IRQ for ep1out: 01000408 ISP , ep_traddr: ffd508ac ep_last_sid: 00000000 use_streams: 0 irq/241-5b13000-2154 [000] d..1 1293.680858: cdns3_complete_trb: ep1out: trb 0000000021a11b54, dma buf: 0xffd50420, size: 16384, burst: 128 ctrl: 0x00001810 (C=0, T=0, CHAIN, LINK) SID:0 LAST_SID:0 irq/241-5b13000-2154 [000] d..1 1293.680865: cdns3_request_handled: Req: 00000000afbccb7d not handled, DMA pos: 185, ep deq: 88, ep enq: 185, start trb: 184, end trb: 184 Actually DMA pos already bigger than previous submit request afbccb7d's TRB (184-184). The reason of (not handled) is that deq position is wrong. The TRB link is below when irq happen. DEQ LINK LINK LINK LINK LINK .... TRB(afbccb7d):START DMA(EP_TRADDR). Original code check LINK TRB, but DEQ just move one step. LINK DEQ LINK LINK LINK LINK .... TRB(afbccb7d):START DMA(EP_TRADDR). This patch skip all LINK TRB and sync DEQ to trb's start. LINK LINK LINK LINK LINK .... DEQ = TRB(afbccb7d):START DMA(EP_TRADDR). Acked-by:
Peter Chen <peter.chen@kernel.org> Cc: stable <stable@vger.kernel.org> Signed-off-by:
Frank Li <Frank.Li@nxp.com> Signed-off-by:
Jun Li <jun.li@nxp.com> Link: https://lore.kernel.org/r/20211130154239.8029-1-Frank.Li@nxp.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Badhri Jagan Sridharan authored
commit fbcd13df upstream. Stub from the spec: "4.5.2.2.4.2 Exiting from AttachWait.SNK State A Sink shall transition to Unattached.SNK when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce. A DRP shall transition to Unattached.SRC when the state of both the CC1 and CC2 pins is SNK.Open for at least tPDDebounce." This change makes TCPM to wait in SNK_DEBOUNCED state until CC1 and CC2 pins is SNK.Open for at least tPDDebounce. Previously, TCPM resets the port if vbus is not present in PD_T_PS_SOURCE_ON. This causes TCPM to loop continuously when connected to a faulty power source that does not present vbus. Waiting in SNK_DEBOUNCED also ensures that TCPM is adherant to "4.5.2.2.4.2 Exiting from AttachWait.SNK State" requirements. [ 6169.280751] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected] [ 6169.280759] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS] [ 6169.280771] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS] [ 6169.282427] CC1: 0 -> 0, CC2: 5 -> 5 [state SNK_ATTACH_WAIT, polarity 0, connected] [ 6169.450825] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [ 6169.450834] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS] [ 6169.930892] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms] [ 6169.931296] disable vbus discharge ret:0 [ 6169.931301] Setting usb_comm capable false [ 6169.932783] Setting voltage/current limit 0 mV 0 mA [ 6169.932802] polarity 0 [ 6169.933706] Requesting mux state 0, usb-role 0, orientation 0 [ 6169.936689] cc:=0 [ 6169.936812] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS] [ 6169.937157] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected] [ 6170.036880] state change PORT_RESET -> PORT_RESET_WAIT_OFF [delayed 100 ms] [ 6170.036890] state change PORT_RESET_WAIT_OFF -> SNK_UNATTACHED [rev2 NONE_AMS] [ 6170.036896] Start toggling [ 6170.041412] CC1: 0 -> 0, CC2: 0 -> 0 [state TOGGLING, polarity 0, disconnected] [ 6170.042973] CC1: 0 -> 0, CC2: 0 -> 5 [state TOGGLING, polarity 0, connected] [ 6170.042976] state change TOGGLING -> SNK_ATTACH_WAIT [rev2 NONE_AMS] [ 6170.042981] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev2 NONE_AMS] [ 6170.213014] state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED [delayed 170 ms] [ 6170.213019] pending state change SNK_DEBOUNCED -> PORT_RESET @ 480 ms [rev2 NONE_AMS] [ 6170.693068] state change SNK_DEBOUNCED -> PORT_RESET [delayed 480 ms] [ 6170.693304] disable vbus discharge ret:0 [ 6170.693308] Setting usb_comm capable false [ 6170.695193] Setting voltage/current limit 0 mV 0 mA [ 6170.695210] polarity 0 [ 6170.695990] Requesting mux state 0, usb-role 0, orientation 0 [ 6170.701896] cc:=0 [ 6170.702181] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev2 NONE_AMS] [ 6170.703343] CC1: 0 -> 0, CC2: 5 -> 0 [state PORT_RESET, polarity 0, disconnected] Fixes: f0690a25 ("staging: typec: USB Type-C Port Manager (tcpm)") Cc: stable@vger.kernel.org Acked-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by:
Badhri Jagan Sridharan <badhri@google.com> Link: https://lore.kernel.org/r/20211130001825.3142830-1-badhri@google.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ole Ernst authored
commit d2a00403 upstream. This is another branded 8153 device that doesn't work well with LPM: r8152 2-2.1:1.0 enp0s13f0u2u1: Stop submitting intr, status -71 Disable LPM to resolve the issue. Signed-off-by:
Ole Ernst <olebowle@gmx.com> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20211127090546.52072-1-olebowle@gmx.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Mathias Nyman authored
commit 09f736aa upstream. Turns out some xHC controllers require all 64 bits in the CRCR register to be written to execute a command abort. The lower 32 bits containing the command abort bit is written first. In case the command ring stops before we write the upper 32 bits then hardware may use these upper bits to set the commnd ring dequeue pointer. Solve this by making sure the upper 32 bits contain a valid command ring dequeue pointer. The original patch that only wrote the first 32 to stop the ring went to stable, so this fix should go there as well. Fixes: ff0e50d3 ("xhci: Fix command ring pointer corruption while aborting a command") Cc: stable@vger.kernel.org Tested-by:
Pavankumar Kondeti <quic_pkondeti@quicinc.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Maciej W. Rozycki authored
commit 3dfac26e upstream. Fix a division by zero in `vgacon_resize' with a backtrace like: vgacon_resize vc_do_resize vgacon_init do_bind_con_driver do_unbind_con_driver fbcon_fb_unbind do_unregister_framebuffer do_register_framebuffer register_framebuffer __drm_fb_helper_initial_config_and_unlock drm_helper_hpd_irq_event dw_hdmi_irq irq_thread kthread caused by `c->vc_cell_height' not having been initialized. This has only started to trigger with commit 860dafa9 ("vt: Fix character height handling with VT_RESIZEX"), however the ultimate offender is commit 50ec42ed ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console"). Said commit has added a call to `vc_resize' whenever `vgacon_init' is called with the `init' argument set to 0, which did not happen before. And the call is made before a key vgacon boot parameter retrieved in `vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to use to the console structure being worked on. Previously the parameter was `c->vc_font.height' and now it is `c->vc_cell_height'. In this particular scenario the registration of fbcon has failed and vt resorts to vgacon. Now fbcon does have initialized `c->vc_font.height' somehow, unlike `c->vc_cell_height', which is why this code did not crash before, but either way the boot parameters should have been copied to the console structure ahead of the call to `vc_resize' rather than afterwards, so that first the call has a chance to use them and second they do not change the console structure to something possibly different from what was used by `vc_resize'. Move the propagation of the vgacon boot parameters ahead of the call to `vc_resize' then. Adjust the comment accordingly. Fixes: 50ec42ed ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console") Cc: stable@vger.kernel.org # v2.6.18+ Reported-by:
Wim Osterholt <wim@djo.tudelft.nl> Reported-by:
Pavel V. Panteleev <panteleev_p@mcst.ru> Signed-off-by:
Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.uk Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Helge Deller authored
commit afdb4a5b upstream. In commit c8c37359 ("parisc: Enhance detection of synchronous cr16 clocksources") I assumed that CPUs on the same physical core are syncronous. While booting up the kernel on two different C8000 machines, one with a dual-core PA8800 and one with a dual-core PA8900 CPU, this turned out to be wrong. The symptom was that I saw a jump in the internal clocks printed to the syslog and strange overall behaviour. On machines which have 4 cores (2 dual-cores) the problem isn't visible, because the current logic already marked the cr16 clocksource unstable in this case. This patch now marks the cr16 interval timers unstable if we have more than one CPU in the system, and it fixes this issue. Fixes: c8c37359 ("parisc: Enhance detection of synchronous cr16 clocksources") Signed-off-by:
Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> # v5.15+ Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Helge Deller authored
commit 0f9fee4c upstream. On newer debian releases the debian-provided "installkernel" script is installed in /usr/sbin. Fix the kernel install.sh script to look for the script in this directory as well. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> # v3.13+ Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Helge Deller authored
commit 1d7c29b7 upstream. Default KBUILD_IMAGE to $(boot)/bzImage if a self-extracting (CONFIG_PARISC_SELF_EXTRACT=y) kernel is to be built. This fixes the bindeb-pkg make target. Signed-off-by:
Helge Deller <deller@gmx.de> Cc: <stable@vger.kernel.org> # v4.14+ Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Al Cooper authored
[ Upstream commit 9cabe26e ] There is a small window in time during resume where the hardware flow control signal RTS can be asserted (which allows a sender to resume sending data to the UART) but the baud rate has not yet been restored. This will cause corrupted data and FRAMING, OVERRUN and BREAK errors. This is happening because the MCTRL register is shadowed in uart_port struct and is later used during resume to set the MCTRL register during both serial8250_do_startup() and uart_resume_port(). Unfortunately, serial8250_do_startup() happens before the UART baud rate is restored. The fix is to clear the shadowed mctrl value at the end of suspend and restore it at the end of resume. Fixes: 41a46948 ("serial: 8250: Add new 8250-core based Broadcom STB driver") Acked-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
Al Cooper <alcooperx@gmail.com> Link: https://lore.kernel.org/r/20211201201402.47446-1-alcooperx@gmail.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Tariq Toukan authored
[ Upstream commit 4cce2ccf ] Transport Interface Receive (TIR) objects perform the packet processing and reassembly and is also responsible for demultiplexing the packets into the different RQs. There are certain TIR context attributes that propagate to the pointed RQs and applied to them (like packet_merge offloads (LRO/SHAMPO) and tunneled_offload_en). When TIRs do not agree on attributes values, a "last one wins" policy is applied. Hence, if not synced properly, a race between TIR params update and a concurrent TIR create/modify operation might yield to a mismatch between the shadow parameters in SW and the actual applied state of the RQs in HW. tunneled_offload_en is a fixed attribute per profile, while packet merge offload state might be toggled and get out-of-sync. When this happens, packet_merge offload might be working although not requested, or the opposite. All updates to packet_merge state and all create/modify operations of regular redirection/steering TIRs are done under the same priv->state_lock, so they do not run in parallel, and no race is possible. However, there are other kind of TIRs (acceleration offloads TIRs, like TLS TIRs) which are created on demand for each new connection without holding the coarse priv->state_lock, hence might race. Fix this by synchronizing all packet_merge state reads and writes against all TIR create/modify operations. Include the modify operations of the regular redirection steering TIRs under the new lock, for better code layering and division of responsibilities. Fixes: 1182f365 ("net/mlx5e: kTLS, Add kTLS RX HW offload support") Signed-off-by:
Tariq Toukan <tariqt@nvidia.com> Reviewed-by:
Moshe Shemesh <moshe@nvidia.com> Reviewed-by:
Maxim Mikityanskiy <maximmi@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Khalid Manaa authored
[ Upstream commit eaee12f0 ] This series introduces new packet merge type, therefore rename lro functions to packet merge to support the new merge type: - Generalize + rename mlx5e_build_tir_ctx_lro to mlx5e_build_tir_ctx_packet_merge. - Rename mlx5e_modify_tirs_lro to mlx5e_modify_tirs_packet_merge. - Rename lro bit in mlx5_ifc_modify_tir_bitmask_bits to packet_merge. - Rename lro_en in mlx5e_params to packet_merge_type type and combine packet_merge params into one struct mlx5e_packet_merge_param. Signed-off-by:
Khalid Manaa <khalidm@nvidia.com> Signed-off-by:
Ben Ben-Ishay <benishay@nvidia.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Ben Ben-Ishay authored
[ Upstream commit 50f477fe ] TIR stands for transport interface receive, the TIR object is responsible for performing all transport related operations on the receive side like packet processing, demultiplexing the packets to different RQ's, etc. lro_timeout is a field in the TIR that is used to set the timeout for lro session, this series introduces new packet merge type, therefore rename lro_timeout to packet_merge_timeout for all packet merge types. Signed-off-by:
Ben Ben-Ishay <benishay@nvidia.com> Reviewed-by:
Tariq Toukan <tariqt@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Sean Christopherson authored
[ Upstream commit 4b85c921 ] Drop the "flush" param and return values to/from the TDP MMU's helper for zapping collapsible SPTEs. Because the helper runs with mmu_lock held for read, not write, it uses tdp_mmu_zap_spte_atomic(), and the atomic zap handles the necessary remote TLB flush. Similarly, because mmu_lock is dropped and re-acquired between zapping legacy MMUs and zapping TDP MMUs, kvm_mmu_zap_collapsible_sptes() must handle remote TLB flushes from the legacy MMU before calling into the TDP MMU. Fixes: e2209710 ("KVM: x86/mmu: Skip rmap operations if rmaps not allocated") Signed-off-by:
Sean Christopherson <seanjc@google.com> Message-Id: <20211120045046.3940942-4-seanjc@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
David Matlack authored
[ Upstream commit 610265ea ] slot_handle_leaf is a misnomer because it only operates on 4K SPTEs whereas "leaf" is used to describe any valid terminal SPTE (4K or large page). Rename slot_handle_leaf to slot_handle_level_4k to avoid confusion. Making this change makes it more obvious there is a benign discrepency between the legacy MMU and the TDP MMU when it comes to dirty logging. The legacy MMU only iterates through 4K SPTEs when zapping for collapsing and when clearing D-bits. The TDP MMU, on the other hand, iterates through SPTEs on all levels. The TDP MMU behavior of zapping SPTEs at all levels is technically overkill for its current dirty logging implementation, which always demotes to 4k SPTES, but both the TDP MMU and legacy MMU zap if and only if the SPTE can be replaced by a larger page, i.e. will not spuriously zap 2m (or larger) SPTEs. Opportunistically add comments to explain this discrepency in the code. Signed-off-by:
David Matlack <dmatlack@google.com> Message-Id: <20211019162223.3935109-1-dmatlack@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Sean Christopherson authored
[ Upstream commit 75236f5f ] Return appropriate error codes if setting up the GHCB scratch area for an SEV-ES guest fails. In particular, returning -EINVAL instead of -ENOMEM when allocating the kernel buffer could be confusing as userspace would likely suspect a guest issue. Fixes: 8f423a80 ("KVM: SVM: Support MMIO for an SEV-ES guest") Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by:
Sean Christopherson <seanjc@google.com> Message-Id: <20211109222350.2266045-2-seanjc@google.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Qais Yousef authored
[ Upstream commit 315c4f88 ] Commit d81ae8aa ("sched/uclamp: Fix initialization of struct uclamp_rq") introduced a bug where uclamp_max of the rq is not reset to match the woken up task's uclamp_max when the rq is idle. The code was relying on rq->uclamp_max initialized to zero, so on first enqueue static inline void uclamp_rq_inc_id(struct rq *rq, struct task_struct *p, enum uclamp_id clamp_id) { ... if (uc_se->value > READ_ONCE(uc_rq->value)) WRITE_ONCE(uc_rq->value, uc_se->value); } was actually resetting it. But since commit d81ae8aa changed the default to 1024, this no longer works. And since rq->uclamp_flags is also initialized to 0, neither above code path nor uclamp_idle_reset() update the rq->uclamp_max on first wake up from idle. This is only visible from first wake up(s) until the first dequeue to idle after enabling the static key. And it only matters if the uclamp_max of this task is < 1024 since only then its uclamp_max will be effectively ignored. Fix it by properly initializing rq->uclamp_flags = UCLAMP_FLAG_IDLE to ensure uclamp_idle_reset() is called which then will update the rq uclamp_max value as expected. Fixes: d81ae8aa ("sched/uclamp: Fix initialization of struct uclamp_rq") Signed-off-by:
Qais Yousef <qais.yousef@arm.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by:
Valentin Schneider <Valentin.Schneider@arm.com> Tested-by:
Dietmar Eggemann <dietmar.eggemann@arm.com> Link: https://lkml.kernel.org/r/20211202112033.1705279-1-qais.yousef@arm.com Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Andrew Halaney authored
[ Upstream commit 9ed20baf ] __setup() callbacks expect 1 for success and 0 for failure. Correct the usage here to reflect that. Fixes: 826bfeb3 ("preempt/dynamic: Support dynamic preempt with preempt= boot option") Reported-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Andrew Halaney <ahalaney@redhat.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20211203233203.133581-1-ahalaney@redhat.com Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Lai Jiangshan authored
[ Upstream commit 5c8f6a2e ] In the native case, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is the trampoline stack. But XEN pv doesn't use trampoline stack, so PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is also the kernel stack. In that case, source and destination stacks are identical, which means that reusing swapgs_restore_regs_and_return_to_usermode() in XEN pv would cause %rsp to move up to the top of the kernel stack and leave the IRET frame below %rsp. This is dangerous as it can be corrupted if #NMI / #MC hit as either of these events occurring in the middle of the stack pushing would clobber data on the (original) stack. And, with XEN pv, swapgs_restore_regs_and_return_to_usermode() pushing the IRET frame on to the original address is useless and error-prone when there is any future attempt to modify the code. [ bp: Massage commit message. ] Fixes: 7f2590a1 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries") Signed-off-by:
Lai Jiangshan <laijs@linux.alibaba.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lkml.kernel.org/r/20211126101209.8613-4-jiangshanlai@gmail.com Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Lai Jiangshan authored
[ Upstream commit 1367afaa ] The commit c7589070 ("x86/entry/64: Remove unneeded kernel CR3 switching") removed a CR3 write in the faulting path of load_gs_index(). But the path's FENCE_SWAPGS_USER_ENTRY has no fence operation if PTI is enabled, see spectre_v1_select_mitigation(). Rather, it depended on the serializing CR3 write of SWITCH_TO_KERNEL_CR3 and since it got removed, add a FENCE_SWAPGS_KERNEL_ENTRY call to make sure speculation is blocked. [ bp: Massage commit message and comment. ] Fixes: c7589070 ("x86/entry/64: Remove unneeded kernel CR3 switching") Signed-off-by:
Lai Jiangshan <laijs@linux.alibaba.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20211126101209.8613-3-jiangshanlai@gmail.com Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Lai Jiangshan authored
[ Upstream commit c07e4555 ] Commit 18ec54fd ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations") added FENCE_SWAPGS_{KERNEL|USER}_ENTRY for conditional SWAPGS. In paranoid_entry(), it uses only FENCE_SWAPGS_KERNEL_ENTRY for both branches. This is because the fence is required for both cases since the CR3 write is conditional even when PTI is enabled. But 96b23714 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry") changed the order of SWAPGS and the CR3 write. And it missed the needed FENCE_SWAPGS_KERNEL_ENTRY for the user gsbase case. Add it back by changing the branches so that FENCE_SWAPGS_KERNEL_ENTRY can cover both branches. [ bp: Massage, fix typos, remove obsolete comment while at it. ] Fixes: 96b23714 ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry") Signed-off-by:
Lai Jiangshan <laijs@linux.alibaba.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20211126101209.8613-2-jiangshanlai@gmail.com Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Michael Sterritt authored
[ Upstream commit 1d5379d0 ] Properly type the operands being passed to __put_user()/__get_user(). Otherwise, these routines truncate data for dependent instructions (e.g., INSW) and only read/write one byte. This has been tested by sending a string with REP OUTSW to a port and then reading it back in with REP INSW on the same port. Previous behavior was to only send and receive the first char of the size. For example, word operations for "abcd" would only read/write "ac". With change, the full string is now written and read back. Fixes: f980f9c3 (x86/sev-es: Compile early handler code into kernel image) Signed-off-by:
Michael Sterritt <sterritt@google.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Reviewed-by:
Paolo Bonzini <pbonzini@redhat.com> Reviewed-by:
Marc Orr <marcorr@google.com> Reviewed-by:
Peter Gonda <pgonda@google.com> Reviewed-by:
Joerg Roedel <jroedel@suse.de> Link: https://lkml.kernel.org/r/20211119232757.176201-1-sterritt@google.com Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Jens Axboe authored
[ Upstream commit a226abcd ] We don't want to be retrying task_work creation failure if there's an actual signal pending for the parent task. If we do, then we can enter an infinite loop of perpetually retrying and each retry failing with -ERESTARTNOINTR because a signal is pending. Fixes: 3146cba9 ("io-wq: make worker creation resilient against signals") Reported-by:
Florian Fischer <florian.fl.fischer@fau.de> Link: https://lore.kernel.org/io-uring/20211202165606.mqryio4yzubl7ms5@pasture/ Tested-by:
Florian Fischer <florian.fl.fischer@fau.de> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
José Roberto de Souza authored
[ Upstream commit 72641d8d ] This workarounds are causing hangs, because I missed the fact that it needs to be enabled for all cases and disabled when doing a resolve pass. So KMD only needs to whitelist it and UMD will be the one setting it on per case. This reverts commit 28ec02c9. Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4145 Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Fixes: 28ec02c9 ("drm/i915: Implement Wa_1508744258") Reviewed-by:
Matt Atwood <matthew.s.atwood@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20211119140931.32791-1-jose.souza@intel.com (cherry picked from commit f3799ff1) Signed-off-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Matt Johnston authored
[ Upstream commit 76d00160 ] We need to test against the existing route type, not the rtm_type in the netlink request. Fixes: 83f0a0b7 ("mctp: Specify route types, require rtm_type in RTM_*ROUTE messages") Signed-off-by:
Matt Johnston <matt@codeconstruct.com.au> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Dan Carpenter authored
[ Upstream commit bfbb307c ] The error paths in the prepare_vmcs02() function are supposed to set *entry_failure_code but this path does not. It leads to using an uninitialized variable in the caller. Fixes: 71f73470 ("KVM: nVMX: Load GUEST_IA32_PERF_GLOBAL_CTRL MSR on VM-Entry") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Message-Id: <20211130125337.GB24578@kili> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Like Xu authored
[ Upstream commit cb1d220d ] If we run the following perf command in an AMD Milan guest: perf stat \ -e cpu/event=0x1d0/ \ -e cpu/event=0x1c7/ \ -e cpu/umask=0x1f,event=0x18e/ \ -e cpu/umask=0x7,event=0x18e/ \ -e cpu/umask=0x18,event=0x18e/ \ ./workload dmesg will report a #GP warning from an unchecked MSR access error on MSR_F15H_PERF_CTLx. This is because according to APM (Revision: 4.03) Figure 13-7, the bits [35:32] of AMD PerfEvtSeln register is a part of the event select encoding, which extends the EVENT_SELECT field from 8 bits to 12 bits. Opportunistically update pmu->reserved_bits for reserved bit 19. Reported-by:
Jim Mattson <jmattson@google.com> Fixes: ca724305 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM") Signed-off-by:
Like Xu <likexu@tencent.com> Message-Id: <20211118130320.95997-1-likexu@tencent.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Dmytro Linkin authored
[ Upstream commit 5c4e8ae7 ] If log_esw_max_sched_depth is not supported group pointer of the vport is NULL. Hence, check the pointer before reading bw_share value. Fixes: 0fe132ea ("net/mlx5: E-switch, Allow to add vports to rate groups") Signed-off-by:
Dmytro Linkin <dlinkin@nvidia.com> Reviewed-by:
Roi Dayan <roid@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Mark Bloch authored
[ Upstream commit 43a0696f ] Always use MLX5_FLOW_TABLE_OTHER_VPORT flag when creating egress ACL table for single FDB. Not doing so on BlueField will make firmware fail the command. On BlueField the E-Switch manager is the ECPF (vport 0xFFFE) which is filled in the flow table creation command but as the other_vport field wasn't set the firmware complains about a bad parameter. This is different from a regular HCA where the E-Switch manager vport is the PF (vport 0x0). Passing MLX5_FLOW_TABLE_OTHER_VPORT will make the firmware happy both on BlueField and on regular HCAs without special condition for each. This fixes the bellow firmware syndrome: mlx5_cmd_check:819:(pid 571): CREATE_FLOW_TABLE(0x930) op_mod(0x0) failed, status bad parameter(0x3), syndrome (0x754a4) Fixes: db202995 ("net/mlx5: E-Switch, add logic to enable shared FDB") Signed-off-by:
Mark Bloch <mbloch@nvidia.com> Reviewed-by:
Maor Gottlieb <maorg@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Dmytro Linkin authored
[ Upstream commit 1e59b32e ] To enable transmit schduler on vport FW require non-zero configuration for vport's TSAR. If vport added to the group which has configured BW share value and TX rate values of the vport are zero, then scheduler wouldn't be enabled on this vport. Fix that by calling BW normalization if BW share of the new group is configured. Fixes: 0fe132ea ("net/mlx5: E-switch, Allow to add vports to rate groups") Signed-off-by:
Dmytro Linkin <dlinkin@nvidia.com> Reviewed-by:
Roi Dayan <roid@nvidia.com> Reviewed-by:
Parav Pandit <parav@nvidia.com> Reviewed-by:
Mark Bloch <mbloch@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Moshe Shemesh authored
[ Upstream commit e45c0b34 ] When the device is in internal error state, command interface isn't accessible and the driver decides which commands to fail and which to ignore. Move the MODIFY_RQT command to the ignore list in order to avoid the following redundant warning messages in internal error state: mlx5_core 0000:82:00.1: mlx5e_rss_disable:419:(pid 23754): Failed to redirect RQT 0x0 to drop RQ 0xc00848: err = -5 mlx5_core 0000:82:00.1: mlx5e_rx_res_channels_deactivate:598:(pid 23754): Failed to redirect direct RQT 0x1 to drop RQ 0xc00848 (channel 0): err = -5 mlx5_core 0000:82:00.1: mlx5e_rx_res_channels_deactivate:607:(pid 23754): Failed to redirect XSK RQT 0x19 to drop RQ 0xc00848 (channel 0): err = -5 Fixes: 43ec0f41 ("net/mlx5e: Hide all implementation details of mlx5e_rx_res") Signed-off-by:
Moshe Shemesh <moshe@nvidia.com> Signed-off-by:
Saeed Mahameed <saeedm@nvidia.com> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-