Select Git revision
Search by author
- Any Author
- authors
-
Angus Ainslie
angus.ainslie
-
Eric Kuzmenko
eric.kuzmenko
-
Evangelos Ribeiro Tzaras
evangelos.tzaras
-
Francois Techene
francois.techene
-
Guido Gunther
guido.gunther
-
JC Staudt
jcstaudt
-
Jonathon Hall
jonathon.hall
-
Julian Sparber
julian.sparber
-
Martin Kepplinger
martin.kepplinger
-
Mohammed Sadiq
mohammed.sadiq
-
Richard Kolla
richard.kolla
-
Sam Hewitt sam.hewitt
-
Sebastian Krzyszkowiak
sebastian.krzyszkowiak
- Jun 18, 2020
-
-
Miao-chen Chou authored
This adds the request handler of MGMT_OP_READ_ADV_MONITOR_FEATURES command. Since the controller-based monitoring is not yet in place, this report only the supported features but not the enabled features. The following test was performed. - Issuing btmgmt advmon-features. Signed-off-by:
-
Miao-chen Chou authored
This adds support for Advertisement Monitor API. Here are the commands and events added. - Read Advertisement Monitor Feature command - Add Advertisement Pattern Monitor command - Remove Advertisement Monitor command - Advertisement Monitor Added event - Advertisement Monitor Removed event Signed-off-by:
-
Abhishek Pandit-Subedi authored
Add the get device flags and set device flags mgmt ops and the device flags changed event. Their behavior is described in detail in mgmt-api.txt in bluez. Sample btmon trace when a HID device is added (trimmed to 75 chars): @ MGMT Command: Unknown (0x0050) plen 11 {0x0001} [hci0] 18:06:14.98 90 c5 13 cd f3 cd 02 01 00 00 00 ........... @ MGMT Event: Unknown (0x002a) plen 15 {0x0004} [hci0] 18:06:14.98 90 c5 13 cd f3 cd 02 01 00 00 00 01 00 00 00 ............... @ MGMT Event: Unknown (0x002a) plen 15 {0x0003} [hci0] 18:06:14.98 90 c5 13 cd f3 cd 02 01 00 00 00 01 00 00 00 ............... @ MGMT Event: Unknown (0x002a) plen 15 {0x0002} [hci0] 18:06:14.98 90 c5 13 cd f3 cd 02 01 00 00 00 01 00 00 00 ............... @ MGMT Event: Command Compl.. (0x0001) plen 10 {0x0001} [hci0] 18:06:14.98 Unknown (0x0050) plen 7 Status: Success (0x00) 90 c5 13 cd f3 cd 02 ....... @ MGMT Command: Add Device (0x0033) plen 8 {0x0001} [hci0] 18:06:14.98 LE Address: CD:F3:CD:13:C5:90 (Static) Action: Auto-connect remote device (0x02) @ MGMT Event: Device Added (0x001a) plen 8 {0x0004} [hci0] 18:06:14.98 LE Address: CD:F3:CD:13:C5:90 (Static) Action: Auto-connect remote device (0x02) @ MGMT Event: Device Added (0x001a) plen 8 {0x0003} [hci0] 18:06:14.98 LE Address: CD:F3:CD:13:C5:90 (Static) Action: Auto-connect remote device (0x02) @ MGMT Event: Device Added (0x001a) plen 8 {0x0002} [hci0] 18:06:14.98 LE Address: CD:F3:CD:13:C5:90 (Static) Action: Auto-connect remote device (0x02) @ MGMT Event: Unknown (0x002a) plen 15 {0x0004} [hci0] 18:06:14.98 90 c5 13 cd f3 cd 02 01 00 00 00 01 00 00 00 ............... @ MGMT Event: Unknown (0x002a) plen 15 {0x0003} [hci0] 18:06:14.98 90 c5 13 cd f3 cd 02 01 00 00 00 01 00 00 00 ............... @ MGMT Event: Unknown (0x002a) plen 15 {0x0002} [hci0] 18:06:14.98 90 c5 13 cd f3 cd 02 01 00 00 00 01 00 00 00 ............... @ MGMT Event: Unknown (0x002a) plen 15 {0x0001} [hci0] 18:06:14.98 90 c5 13 cd f3 cd 02 01 00 00 00 01 00 00 00 ............... Signed-off-by: -
Abhishek Pandit-Subedi authored
Replace the wakeable boolean with flags in hci_conn_params and all users of this boolean. This will be used by the get/set device flags mgmt op. Signed-off-by:
-
Abhishek Pandit-Subedi authored
Since the classic device list now supports flags, convert the wakeable list into a flag on the existing device list. Signed-off-by:
-
Abhishek Pandit-Subedi authored
In order to more easily add device flags to classic devices, create a new type of bdaddr_list that supports setting flags. Signed-off-by:
-
Marcel Holtmann authored
This adds the required read/set commands for runtime configuration. Even while currently no parameters are specified, the commands are made available. Signed-off-by:
-
- Jun 12, 2020
-
-
Alain Michaud authored
This patch implements the read default system parameters and the set default system parameters mgmt commands. Signed-off-by:
-
Alain Michaud authored
This patch centralized the initialization of default parameters. This is required to allow clients to more easily customize the default system parameters. Signed-off-by:
-
Alain Michaud authored
This patch submits the corresponding kernel definitions to mgmt.h. This is submitted before the implementation to avoid any conflicts in values allocations. Signed-off-by:
-
Balakrishna Godavarthi authored
Tx pending flag is set to true when HOST IBS state is AWAKE or AWAKEING. If IBS state is ASLEEP, then Tx clock is already voted off. To optimize further directly calling serial_clock_vote() instead of qca_wq_serial_tx_clock_vote_off(), at this point of qca_suspend() already data is sent out. No need to wake up hci to send data. Signed-off-by:
-
Balakrishna Godavarthi authored
In some version of WCN399x, SoC idle timeout is configured as 80ms instead of 20ms or 40ms. To honor all the SoC's supported in the driver increasing SoC idle timeout to 200ms. Fixes: 41d5b25f ("Bluetooth: hci_qca: add PM support") Signed-off-by:
-
Balakrishna Godavarthi authored
By default, WCN3991 sent debug packets to HOST via ACL packet with header 0xDC2E. This logging is not required on commercial devices. With this patch SoC logging is disabled post fw download. Signed-off-by:
-
Alain Michaud authored
This change implements suggestions from the code review of the SCO CMSG state flag patch. Signed-off-by:
-
Alain Michaud authored
This change adds support for reporting the BT_PKT_STATUS to the socket CMSG data to allow the implementation of a packet loss correction on erroneous data received on the SCO socket. The patch was partially developed by Marcel Holtmann and validated by Hsin-yu Chao. Signed-off-by:
-
Abhishek Pandit-Subedi authored
Use device_init_wakeup to allow the Bluetooth dev to wake the system from suspend. Currently, the device can wake the system but no power/wakeup entry is created in sysfs to allow userspace to disable wakeup. Signed-off-by:
-
Abhishek Pandit-Subedi authored
Use the parent device's power/wakeup to control whether we support remote wake. If remote wakeup is disabled, Bluetooth will not enable scanning for incoming connections. Signed-off-by:
-
Abhishek Pandit-Subedi authored
Set the correct parent dev when registering hdev. This allows userspace tools to find the parent device (for example, to set the power/wakeup property). Before this change, the path was /sys/devices/virtual/bluetooth/hci0 and after this change, it looks more like: /sys/bus/mmc/devices/mmc1:0001/mmc1:0001:2/bluetooth/hci0 Signed-off-by:
-
- Jun 10, 2020
-
-
Chethan T N authored
This patch shall enable the Intel telemetry exception format based on the supported features Signed-off-by:
-
Chethan T N authored
The command shall read the Intel controller supported debug feature. Based on the supported features additional debug configuration shall be enabled. Signed-off-by:
-
Venkata Lakshmi Narayana Gubba authored
Due to race conditions between qca_hw_error and qca_controller_memdump during SSR timeout,the same pointer is freed twice. This results in a double free. Now a lock is acquired before checking the stauts of SSR state. Fixes: d841502c ("Bluetooth: hci_qca: Collect controller memory dump during SSR") Signed-off-by:
-
- Jun 08, 2020
-
-
Abhishek Pandit-Subedi authored
It is preferable to allow suspend even when Bluetooth has problems preparing for sleep. When Bluetooth fails to finish preparing for suspend, log the error and allow the suspend notifier to continue instead. To also make it clearer why suspend failed, change bt_dev_dbg to bt_dev_err when handling the suspend timeout. Fixes: dd522a74 ("Bluetooth: Handle LE devices during suspend") Reported-by:
-
Matthias Kaehlcke authored
If waiting for IBS sleep times out jump to the error handler, this is easier to read than multiple 'if' branches and a fall through to the error handler. Signed-off-by:
-
Matthias Kaehlcke authored
qca_suspend() calls serdev_device_wait_until_sent() regardless of whether a transfer is pending. While it does no active harm since the function should return immediately it makes the code more confusing. Add a flag to track whether a transfer is pending and only call serdev_device_wait_until_sent() is needed. Signed-off-by:
-
Matthias Kaehlcke authored
qca_suspend() removes the vote for the UART TX clock after writing an IBS sleep request to the serial buffer. This is not a good idea since there is no guarantee that the request has been sent at this point. Instead remove the vote after successfully entering IBS sleep. This also fixes the issue of the vote being removed in case of an aborted suspend due to a failure of entering IBS sleep. Fixes: 41d5b25f ("Bluetooth: hci_qca: add PM support") Signed-off-by:
-
Matthias Kaehlcke authored
The serial clocks should be on when there is a vote for at least one of the clocks (RX or TX), and off when there is no 'on' vote. The current logic to determine the combined state is a bit redundant in the code paths for different types of votes, use a single statement in the common path instead. Signed-off-by:
-
- Jun 03, 2020
-
-
Dan Carpenter authored
When a function like devm_clk_get_optional() function returns both error pointers on error and NULL then the NULL return means that the optional feature is deliberately disabled. It is a special sort of success and should not trigger an error message. The surrounding code should be written to check for NULL and not crash. On the other hand, if we encounter an error, then the probe from should clean up and return a failure. In this code, if devm_clk_get_optional() returns an error pointer then the kernel will crash inside the call to: clk_set_rate(qcadev->susclk, SUSCLK_RATE_32KHZ); The error handling must be updated to prevent that. Fixes: 77131dfe ("Bluetooth: hci_qca: Replace devm_gpiod_get() with devm_gpiod_get_optional()") Signed-off-by:
-
Alain Michaud authored
This patch removes a particularly noisy dbg message. The debug message isn't particularly interesting for debuggability so it was simply removed to reduce noise in dbg logs. Signed-off-by:
-
Manish Mandlik authored
Check current scan state by checking HCI_LE_SCAN flag and send scan disable command only if scan is already enabled. Signed-off-by:
-
- Jun 01, 2020
-
-
Pali Rohár authored
Firmware for sd8997 chipset is distributed by Marvell package and also as part of the linux-firmware repository in filename sdsd8997_combo_v4.bin. This patch fixes mwifiex driver to load correct firmware file for sd8997. Fixes: f0ef6748 ("Bluetooth: btmrvl: add sd8997 chipset support") Signed-off-by:
-
Pali Rohár authored
Firmware for sd8977 chipset is distributed by Marvell package and also as part of the linux-firmware repository in filename sdsd8977_combo_v2.bin. This patch fixes mwifiex driver to load correct firmware file for sd8977. Fixes: 8c57983b ("Bluetooth: btmrvl: add support for sd8977 chipset") Signed-off-by:
-
Pali Rohár authored
Firmware for sd8997 chipset is distributed by Marvell package and also as part of the linux-firmware repository in filename sdsd8997_combo_v4.bin. This patch fixes mwifiex driver to load correct firmware file for sd8997. Fixes: 6d85ef00 ("mwifiex: add support for 8997 chipset") Signed-off-by:
-
Pali Rohár authored
Firmware for sd8977 chipset is distributed by Marvell package and also as part of the linux-firmware repository in filename sdsd8977_combo_v2.bin. This patch fixes mwifiex driver to load correct firmware file for sd8977. Fixes: 1a0f5478 ("mwifiex: add support for sd8977 chipset") Signed-off-by:
-
- Jun 02, 2020
-
-
Thadeu Lima de Souza Cascardo authored
When running with conntrack rules, the dropped overlap fragments may cause EPERM to be returned to sendto. Instead of completely failing, just ignore those errors and continue. If this causes packets with overlap fragments to be dropped as expected, that is okay. And if it causes packets that are expected to be received to be dropped, which should not happen, it will be detected as failure. Signed-off-by:
-
Vasily Averin authored
found by smatch: drivers/net/net_failover.c:65 net_failover_open() error: we previously assumed 'primary_dev' could be null (see line 43) Fixes: cfc80d9a ("net: Introduce net_failover driver") Signed-off-by:
-
David S. Miller authored
Tuong Lien says: ==================== tipc: revert two patches We revert two patches: tipc: Fix potential tipc_node refcnt leak in tipc_rcv tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv which prevented TIPC encryption from working properly and caused kernel panic. ==================== Signed-off-by: -
Tuong Lien authored
This reverts commit 441870ee. Like the previous patch in this series, we revert the above commit that causes similar issues with the 'aead' object. Acked-by:
-
Tuong Lien authored
This reverts commit de058420. There is no actual tipc_node refcnt leak as stated in the above commit. The refcnt is hold carefully for the case of an asynchronous decryption (i.e. -EINPROGRESS/-EBUSY and skb = NULL is returned), so that the node object cannot be freed in the meantime. The counter will be re-balanced when the operation's callback arrives with the decrypted buffer if any. In other cases, e.g. a synchronous crypto the counter will be decreased immediately when it is done. Now with that commit, a kernel panic will occur when there is no node found (i.e. n = NULL) in the 'tipc_rcv()' or a premature release of the node object. This commit solves the issues by reverting the said commit, but keeping one valid case that the 'skb_linearize()' is failed. Acked-by:
-
Ronak Doshi authored
It makes sense to allow changes to get/set rx flow hash callback only when rss is enabled. This patch restricts get_rss_hash_opts and set_rss_hash_opts methods to allow querying and configuring different Rx flow hash configurations only when rss is enabled Signed-off-by:
-
Luo bin authored
add support to change TX/RX queue number with "ethtool -L combined". V5 -> V6: remove check for carrier in hinic_xmit_frame V4 -> V5: change time zone in patch header V3 -> V4: update date in patch header V2 -> V3: remove check for zero channels->combined_count V1 -> V2: update commit message("ethtool -L" to "ethtool -L combined") V0 -> V1: remove check for channels->tx_count/rx_count/other_count Signed-off-by:
-