- Dec 02, 2008
-
-
Nick Piggin authored
Jim Radford has reported that the vmap subsystem rewrite was sometimes causing his VIVT ARM system to behave strangely (seemed like going into infinite loops trying to fault in pages to userspace). We determined that the problem was most likely due to a cache aliasing issue. flush_cache_vunmap was only being called at the moment the page tables were to be taken down, however with lazy unmapping, this can happen after the page has subsequently been freed and allocated for something else. The dangling alias may still have dirty data attached to it. The fix for this problem is to do the cache flushing when the caller has called vunmap -- it would be a bug for them to write anything else to the mapping at that point. That appeared to solve Jim's problems. Reported-by:
Jim Radford <radford@blackbean.org> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2Linus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: ocfs2: fix regression in ocfs2_read_blocks_sync() ocfs2: fix return value set in init_dlmfs_fs() ocfs2: Small documentation update ocfs2: fix wake_up in unlock_ast ocfs2: initialize stack_user lvbptr ocfs2: comments typo fix
-
- Dec 01, 2008
-
-
Mark Fasheh authored
We're panicing in ocfs2_read_blocks_sync() if a jbd-managed buffer is seen. At first glance, this seems ok but in reality it can happen. My test case was to just run 'exorcist'. A struct inode is being pushed out of memory but is then re-read at a later time, before the buffer has been checkpointed by jbd. This causes a BUG to be hit in ocfs2_read_blocks_sync(). Reviewed-by:
-
Coly Li authored
In init_dlmfs_fs(), if calling kmem_cache_create() failed, the code will use return value from calling bdi_init(). The correct behavior should be set status as -ENOMEM before going to "bail:". Signed-off-by:
-
Mark Fasheh authored
Remove some features from the "not-supported" list that are actually supported now. Signed-off-by: -
David Teigland authored
In ocfs2_unlock_ast(), call wake_up() on lockres before releasing the spin lock on it. As soon as the spin lock is released, the lockres can be freed. Signed-off-by:
-
David Teigland authored
The locking_state dump, ocfs2_dlm_seq_show, reads the lvb on locks where it has not yet been initialized by a lock call. Signed-off-by:
-
Coly Li authored
This patch fixes two typos in comments of ocfs2. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-devLinus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: libata: blacklist Seagate drives which time out FLUSH_CACHE when used with NCQ [libata] pata_rb532_cf: fix signature of the xfer function [libata] pata_rb532_cf: fix and rename register definitions ata_piix: add borked Tecra M4 to broken suspend list
-
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infinibandLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: IB/mlx4: Fix MTT leakage in resize CQ IB/ehca: Fix problem with generated flush work completions IB/ehca: Change misleading error message on memory hotplug mlx4_core: Save/restore default port IB capability mask
-
Tejun Heo authored
Some recent Seagate harddrives have firmware bug which causes FLUSH CACHE to timeout under certain circumstances if NCQ is being used. This can be worked around by disabling NCQ and fixed by updating the firmware. Implement ATA_HORKAGE_FIRMWARE_UPDATE and blacklist these devices. The wiki page has been updated to contain information on this issue. http://ata.wiki.kernel.org/index.php/Known_issues Signed-off-by:
-
Phil Sutter authored
Per definition, this function should return the number of bytes consumed. As the original parameter "buflen" is being decremented inside the read/write loop, save it in "retlen" at the beginning. Signed-off-by:
-
Phil Sutter authored
The original standalone driver uses a custom address for the error register. Use it in pata_rb532_cf, too. Rename two register definitions: - The address offset 0x0800 in fact is the ATA base, not ATA command address. - The offset 0x0C00 is not a regular ATA data address, but a buffered one allowing 4-byte IO. Signed-off-by:
-
Tejun Heo authored
Tecra M4 sometimes forget what it is and reports bogus data via DMI which makes the machine evade broken suspend matching and thus fail suspend/resume. This patch updates piix_broken_suspend() such that it can match such case. As the borked DMI data is a bit generic, matching many entries to make the match more specific is necessary. As the usual DMI matching is limited to four entries, this patch uses hard coded manual matching. This is reported by Alexandru Romanescu. Signed-off-by:
-
Roland Dreier authored
-
Jack Morgenstein authored
When resizing a CQ, MTTs associated with the old CQE buffer were not freed. As a result, if any app used resize CQ repeatedly, all MTTs were eventually exhausted, which led to all memory registration operations failing until the driver is reloaded. Once the RESIZE_CQ command returns successfully from FW, FW no longer accesses the old CQ buffer, so it is safe to deallocate the MTT entries used by the old CQ buffer. Finally, if the RESIZE_CQ command fails, the MTTs allocated for the new CQEs buffer also need to be de-allocated. This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=1416 >. Signed-off-by:
-
Stefan Roscher authored
This fix enables ehca device driver to generate flush work completions even if the application doesn't request completions for all work requests. The current implementation of ehca will generate flush work completions for the wrong work requests if an application uses non signaled work completions. Signed-off-by:
-
Joachim Fenkes authored
The error message printed when the eHCA driver prevents memory hotplug is misleading -- the user might think that hot-removing the lhca, hotplugging memory, then hot-adding the lhca again will work, but it actually doesn't. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: ieee1394: sbp2: fix race condition in state change ieee1394: fix list corruption (reported at module removal) firewire: fw-sbp2: another iPod mini quirk entry ieee1394: sbp2: another iPod mini quirk entry
-
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hidLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: HID: Apple ALU wireless keyboards are bluetooth devices HID: remove setup mutex, fix possible deadlock HID: add USB ID for another dual gameron adapter HID: unignore mouse on unibody macbooks HID: fix blacklist entries for greenasia/pantherlord
-
Kevin Hao authored
We alloc a fake tty in usb serial console setup function. we should init the tty's kref otherwise we will face WARN_ON after following invoke of tty_port_tty_set --> tty_kref_get. Signed-off-by:
-
Will Newton authored
When no console is configured tty_open tries to call kref_get on a NULL pointer, return ENODEV instead. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: USB: serial: add more Onda device ids to option driver USB: usb-storage: unusual_devs entry for Nikon D2H USB: storage: unusual_devs entry for Mio C520-GPS USB: fsl_usb2_udc: Report disconnect before unbinding USB: fsl_qe_udc: Report disconnect before unbinding USB: fix SB600 USB subsystem hang bug Revert "USB: improve ehci_watchdog's side effect in CPU power management"
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds authored
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: powerpc: Fix build for 32-bit SMP configs
-
Johannes Weiner authored
The zone's rotation statistics must not be accessed without the corresponding LRU lock held. Fix an unprotected write in shrink_active_list(). Acked-by:
-
Linus Torvalds authored
This reverts commit e669dae6, since it is incomplete, and clashes with fuller patches and the sparc 32/64 unification effort. Requested-by:
-
Greg Kroah-Hartman authored
Thanks to Domenico Riccio for pointing these out. Cc: Domenico Riccio <domenico.riccio@gmail.com> Signed-off-by: -
Tobias Kunze Briseño authored
This patch adds an unusual_devs entry for the Nikon D2H camera. From: Tobias Kunze Briseño <t@fictive.com>, Signed-off-by:
-
Alan Stern authored
This patch (as1176) adds an unusual_devs entry for the Mio C520 GPS unit. Other devices also based on the Mitac hardware use the same USB interface firmware, so the Vendor and Product names are generalized. This fixes Bugzilla #11583. Signed-off-by:
-
Anton Vorontsov authored
Gadgets disable endpoints in their disconnect callbacks, so we must call disconnect before unbinding. The patch fixes following badness: root@b1:~# insmod fsl_usb2_udc.ko Freescale High-Speed USB SOC Device Controller driver (Apr 20, 2007) root@b1:~# insmod g_ether.ko g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC 26:07:ba:c0:44:33 usb0: HOST MAC 96:81:0c:05:4d:e3 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready fsl-usb2-udc: bind to driver g_ether g_ether gadget: high speed config #1: CDC Ethernet (ECM) root@b1:~# rmmod g_ether.ko ------------[ cut here ]------------ Badness at drivers/usb/gadget/composite.c:871 [...] NIP [e10c3454] composite_unbind+0x24/0x15c [g_ether] LR [e10aa454] usb_gadget_unregister_driver+0x13c/0x164 [fsl_usb2_udc] Call Trace: [df145e80] [ffffff94] 0xffffff94 (unreliable) [df145eb0] [e10aa454] usb_gadget_unregister_driver+0x13c/0x164 [fsl_usb2_udc] [df145ed0] [e10c4c40] usb_composite_unregister+0x3c/0x4c [g_ether] [df145ee0] [c006bcc0] sys_delete_module+0x130/0x19c [df145f40] [c00142d8] ret_from_syscall+0x0/0x38 [...] unregistered gadget driver 'g_ether' Signed-off-by:
-
Anton Vorontsov authored
Gadgets disable endpoints in their disconnect callbacks, so we must call disconnect before unbinding. This also fixes muram memory leak, since we free muram in the qe_ep_disable(). But mainly the patch fixes following badness: root@b1:~# insmod fsl_qe_udc.ko fsl_qe_udc: Freescale QE/CPM USB Device Controller driver, 1.0 fsl_qe_udc e01006c0.usb: QE USB controller initialized as device root@b1:~# insmod g_ether.ko g_ether gadget: using random self ethernet address g_ether gadget: using random host ethernet address usb0: MAC be:2d:3c:fa:be:f0 usb0: HOST MAC 62:b8:6a:df:38:66 g_ether gadget: Ethernet Gadget, version: Memorial Day 2008 g_ether gadget: g_ether ready fsl_qe_udc e01006c0.usb: fsl_qe_udc bind to driver g_ether g_ether gadget: high speed config #1: CDC Ethernet (ECM) root@b1:~# rmmod g_ether.ko ------------[ cut here ]------------ Badness at drivers/usb/gadget/composite.c:871 [...] NIP [d10c1374] composite_unbind+0x24/0x15c [g_ether] LR [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc] Call Trace: [cfb93e80] [cfb1f3a0] 0xcfb1f3a0 (unreliable) [cfb93eb0] [d10a82f4] usb_gadget_unregister_driver+0x128/0x168 [fsl_qe_udc] [cfb93ed0] [d10c2a3c] usb_composite_unregister+0x3c/0x4c [g_ether] [cfb93ee0] [c006bde0] sys_delete_module+0x130/0x19c [cfb93f40] [c00142d8] ret_from_syscall+0x0/0x38 [...] fsl_qe_udc e01006c0.usb: unregistered gadget driver 'g_ether' Signed-off-by:
-
Shane Huang authored
This patch is required for all AMD SB600 revisions to avoid USB subsystem hang symptom. The USB subsystem hang symptom is observed when the system has multiple USB devices connected to it. In some cases a USB hub may be required to observe this symptom. Reported in bugzilla as #11599, the similar patch for SB700 old revision is: commit b09bc6cb Reported-by:
-
Greg Kroah-Hartman authored
This reverts commit f0d781d5. It was the wrong thing to do, and does not really do what it said it did. Cc: Yi Yang <yi.y.yang@intel.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Milton Miller authored
attr_smt_snooze_delay is only defined for CONFIG_PPC64, so protect the attribute removal with the same condition. This fixes this build error on 32-bit SMP configurations: /data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c: In function ‘unregister_cpu_online’: /data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: ‘attr_smt_snooze_delay’ undeclared (first use in this function) /data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: (Each undeclared identifier is reported only once /data/home/miltonm/next.git/arch/powerpc/kernel/sysfs.c:722: error: for each function it appears in.) Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/i915: Fix copy'n'pasteo that broke VT switch if flushing was non-empty.
-
git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpcLinus Torvalds authored
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: powerpc: Fix system calls on Cell entered with XER.SO=1 powerpc/cell: Fix GDB watchpoints, again powerpc/mpic: Don't reset affinity for secondary MPIC on boot powerpc/cell/axon-msi: Retry on missing interrupt powerpc: Fix boot freeze on machine with empty memory node powerpc: Fix IRQ assignment for some PCIe devices powerpc/spufs: Fix spinning in spufs_ps_fault on signal powerpc/mpc832x_rdb: fix swapped ethernet ids powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610 powerpc/85xx: L2 cache size wrong in 8572DS dts powerpc/virtex: Update defconfigs powerpc/52xx: update defconfigs xsysace: Fix driver to use resource_size_t instead of unsigned long powerpc/virtex: fix various format/casting printk mismatches powerpc/mpc5200: fix bestcomm Kconfig dependencies powerpc/44x: Fix 460EX/460GT machine check handling powerpc/40x: Limit allocable DRAM during early mapping
-
Linus Torvalds authored
* master.kernel.org:/home/rmk/linux-2.6-arm: Allow architectures to override copy_user_highpage() [ARM] pxa/palmtx: misc fixes to use generic GPIO API ARM: OMAP: Fixes for suspend / resume GPIO wake-up handling [ARM] pxa/corgi: update default config to exclude tosa from being built [ARM] pxa/pcm990: use negative number for an invalid GPIO in camera data ARM: OMAP: Typo fix for clock_allow_idle ARM: OMAP: Remove broken LCD driver for SX1 [ARM] 5335/1: pxa25x_udc: Fix is_vbus_present to return 1 or 0 [ARM] pxa/MioA701: bluetooth resume fix [ARM] pxa/MioA701: fix memory corruption.
-
Eric Anholt authored
Introduced in the "Avoid BUG_ONs on VT switch" commit. Signed-off-by:
-
- Nov 30, 2008
-
-
Paul Mackerras authored
It turns out that on Cell, on a kernel with CONFIG_VIRT_CPU_ACCOUNTING = y, if a program sets the SO (summary overflow) bit in the XER and then does a system call, the SO bit in CR0 will be set on return regardless of whether the system call detected an error. Since CR0.SO is used as the error indication from the system call, this means that all system calls appear to fail. The reason is that the workaround for the timebase bug on Cell uses a compare instruction. With CONFIG_VIRT_CPU_ACCOUNTING = y, the ACCOUNT_CPU_USER_ENTRY macro reads the timebase, so we end up doing a compare instruction, which copies XER.SO to CR0.SO. Since we were doing this in the system call entry patch after clearing CR0.SO but before saving the CR, this meant that the saved CR image had CR0.SO set if XER.SO was set on entry. This fixes it by moving the clearing of CR0.SO to after the ACCOUNT_CPU_USER_ENTRY call in the system call entry path. Signed-off-by:
-
Arnd Bergmann authored
An earlier patch from Jens Osterkamp attempted to fix GDB watchpoints by enabling the DABRX register at boot time. Unfortunately, this did not work on SMP setups, where secondary CPUs were still using the power-on DABRX value. This introduces the same change for secondary CPUs on cell as well. Reported-by:
-