Tags

i.MX arm64 device tree update for 5.6:

 - New board support: i.MX8MQ based Thor96 board, Google i.MX8MQ Phanbell
   board, LX2160A based Solidrun Clearfog CX and Honeycomb boards.
 - Add eLCDIF controller and missing SAI nodes for i.MX8MQ SoC.
 - Add Crypto CAAM support for i.MX8MM and i.MX8MN.
 - Drop unneeded "simple-bus" from anatop node on i.MX8MM and i.MX8MN.
 - Drop unused/undocumented "fsl,aips-bus" and "fsl,imx8mq-aips-bus"
   compatibles from i.MX8M SoCs.
 - Add DDR controller nodes for i.MX8M devices.
 - Add EEPROM description for imx8mq-hummingboard-pulse and
   imx8mq-sr-som boards.
 - Enable USB1 and TypeC support for imx8mn-evk board.
 - Add FlexSPI and QSPI support for a few Layerscape SoCs and boards.
 - Add External MDIO1 node and the two RGMII PHYs connected on LX2160A.
 - Add missing SAI devices and set SAIs into async mode on LS1028A.
 - Other random device additions and enhancement for various platforms.

i.MX device tree update for 5.6:

 - New board support: i.MX6SL based Tolino Shine 3 eBook reader,
   i.MX7ULP Embedded Artists COM Board, i.MX6Q/DL based Gateworks
   Ventana Boards.
 - A couple of series from Andrey Smirnov to enhance i.MX6 RDU2 and
   VF610 ZII boards.
 - Add revision in board compatible string for imx6sx-sdb-reva and
   imx7d-sdb-reva board.
 - A fixup on imx6sl-tolino-shine3 board to remove incorrect power
   supply assignment.
 - Set initial buck regulator modes explicitly for phycore-imx6 board,
   so that a wrong initial mode set by bootloader does not interfere.
 - Add Add LCD support for imx7d-pico board.
 - A couple of patches from Michael Grzeschik to enhance USB Host
   support on i.MX25.
 - A couple of patches from Michael Trimarchi to remove duplicate
   Ethernet PHY reset properties on imx6qdl-icore and switch to
   phy-handle.
 - A couple of changes to add extirq node support on LS1021A SoC and
   make use of it on the LS1021A-TSN board.
 - A few random device additions and improvements on various boards.

Linux 5.5-rc6

i.MX DT bindings update for 5.6:

 - Add compatibles for boards:
     i.MX6 SoloX SDB Rev-A Board
     i.MX7 SabreSD Rev-A Board
     i.MX6SL based Tolino Shine 3 eBook reader
     i.MX7ULP Embedded Artists COM Board
     i.MX8MQ Thor96 Board
     i.MX8MQ based Google Coral Edge TPU
     i.MX6Q/DL based Gateworks Ventana Boards
     LX2160A based QDS and RDB Boards
 - Add missing imx6sll into fsl-pxp bindings.
 - Add i.MX8MQ LCDIF compatible into mxsfb bindings.

i.MX SoC changes for 5.6:

 - Add support for reading serial number from OCOTP on i.MX7ULP.
 - A patch from Anson to enable ARM_ERRATA_814220 for i.MX6UL & i.MX7D,
   and a fixup patch from Arnd to select the option only for ARMv7-A.

i.MX driver changes for 5.6:

 - Add i.MX8MP SoC driver support.
 - Allow IMX DSP Protocol driver to be built as module.
 - Add COMPILE_TEST for IMX_SCU_SOC driver to increase build coverage.
 - Print SoC type and revision in i.MX8 SoC driver, as this is useful
   information to have when looking through boot log.

i.MX fixes for 5.5, round 2:

 - Fix i.MX8MM SDMA1 AHB clock setting to remove a "Timeout waiting for CH0"
   error seen with UART1.
 - Correct compatible of RV3029 RTC device on imx6q-dhcom board.
 - Correct interrupt trigger type for magnetometer on board
   imx8mq-librem5-devkit.
 - A series from Anson Huang to fix vdd3p0 power supplier for a few NXP
   development board.
 - Fix imx6q-icore-mipi board to use 1.5 version of i.Core MX6DL, so
   that Ethernet interface on the board works properly.
 - Fix Toradex Colibri board to get NAND flash support back.
 - Fix SGTL5000 VDDIO regulator connection for imx6q-dhcom, which
   is connected to PMIC SW2 output rather than a fixed 3V3 rail.
 - Fix 'reg' of CPU node on imx7ulp to get rid of a warning given by
   kernel.
 - Fix endian setting for DCFG on LS1028A SoC, so that register access
   of DCFG becomes correct.

linux-5.3.0-librem5-h1 v5.3.0+librem5.8

Linux 5.5-rc5

linux-5.3.0-librem5-h1 v5.3.0+librem5.7

Linux 5.5-rc4

linux-5.3.0-librem5-h1 v5.3.0+librem5.6

Linux 5.5-rc3

linux-5.3.0-librem5-h1 v5.3.0+librem5.5

Linux 5.5-rc2

linux-5.3.0-librem5-h1 v5.3.0+librem5.4

i.MX clock fixes for 5.5:
 - Add missing lock to divider in the composite driver for exclusive
   register access.
 - Add missing sentinel for ulp_div_table in clk-imx7ulp driver.
 - Fix clk_pll14xx_wait_lock() function which calls into
   readl_poll_timeout() with incorrect parameter.

i.MX fixes for 5.5:
 - Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
   so that SPI NOR device can be probed.
 - Fix power button of E60K02 board by removing LDORTC2 regulator.
 - A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
   remove the boot regression caused by 8267ff89b713 ("ARM: imx: Add
   serial number support for i.MX6/7 SoCs").
 - A couple of fixes on LS1028A SoC TMU regarding to calibration data
   and reboot register configuration.
 - Fix a regression seen on imx6ul-evk board by marking always-on for
   the regulator that is shared by many peripherals.
 - Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.

Linux 5.5-rc1

linux-5.3.0-librem5-h1 v5.3.0+librem5.3