Select Git revision
Search by author
- Any Author
- authors
-
Angus Ainslie
angus.ainslie
-
Eric Kuzmenko
eric.kuzmenko
-
Evangelos Ribeiro Tzaras
evangelos.tzaras
-
Francois Techene
francois.techene
-
Guido Gunther
guido.gunther
-
JC Staudt
jcstaudt
-
Jonathon Hall
jonathon.hall
-
Julian Sparber
julian.sparber
-
Martin Kepplinger
martin.kepplinger
-
Mohammed Sadiq
mohammed.sadiq
-
Richard Kolla
richard.kolla
-
Sam Hewitt sam.hewitt
-
Sebastian Krzyszkowiak
sebastian.krzyszkowiak
- Jan 05, 2022
-
-
Chunfeng Yun authored
commit 8c313e3b upstream. This is caused by uninitialization of list_head. BUG: KASAN: use-after-free in __list_del_entry_valid+0x34/0xe4 Call trace: dump_backtrace+0x0/0x298 show_stack+0x24/0x34 dump_stack+0x130/0x1a8 print_address_description+0x88/0x56c __kasan_report+0x1b8/0x2a0 kasan_report+0x14/0x20 __asan_load8+0x9c/0xa0 __list_del_entry_valid+0x34/0xe4 mtu3_req_complete+0x4c/0x300 [mtu3] mtu3_gadget_stop+0x168/0x448 [mtu3] usb_gadget_unregister_driver+0x204/0x3a0 unregister_gadget_item+0x44/0xa4 Fixes: 83374e03 ("usb: mtu3: add tracepoints to help debug") Cc: stable@vger.kernel.org Reported-by:
-
Chunfeng Yun authored
commit a7aae769 upstream. There is a seldom issue that the controller access invalid address and trigger devapc or emimpu violation. That is due to memory access is out of order and cause gpd data is not correct. Add mb() to prohibit compiler or cpu from reordering to make sure GPD is fully written before setting its HWO. Fixes: 48e0d373 ("usb: mtu3: supports new QMU format") Cc: stable@vger.kernel.org Reported-by:
-
Vincent Pelletier authored
commit b1e08873 upstream. ffs_data_clear is indirectly called from both ffs_fs_kill_sb and ffs_ep0_release, so it ends up being called twice when userland closes ep0 and then unmounts f_fs. If userland provided an eventfd along with function's USB descriptors, it ends up calling eventfd_ctx_put as many times, causing a refcount underflow. NULL-ify ffs_eventfd to prevent these extraneous eventfd_ctx_put calls. Also, set epfiles to NULL right after de-allocating it, for readability. For completeness, ffs_data_clear actually ends up being called thrice, the last call being before the whole ffs structure gets freed, so when this specific sequence happens there is a second underflow happening (but not being reported): /sys/kernel/debug/tracing# modprobe usb_f_fs /sys/kernel/debug/tracing# echo ffs_data_clear > set_ftrace_filter /sys/kernel/debug/tracing# echo function > current_tracer /sys/kernel/debug/tracing# echo 1 > tracing_on (setup gadget, run and kill function userland process, teardown gadget) /sys/kernel/debug/tracing# echo 0 > tracing_on /sys/kernel/debug/tracing# cat trace smartcard-openp-436 [000] ..... 1946.208786: ffs_data_clear <-ffs_data_closed smartcard-openp-431 [000] ..... 1946.279147: ffs_data_clear <-ffs_data_closed smartcard-openp-431 [000] .n... 1946.905512: ffs_data_clear <-ffs_data_put Warning output corresponding to above trace: [ 1946.284139] WARNING: CPU: 0 PID: 431 at lib/refcount.c:28 refcount_warn_saturate+0x110/0x15c [ 1946.293094] refcount_t: underflow; use-after-free. [ 1946.298164] Modules linked in: usb_f_ncm(E) u_ether(E) usb_f_fs(E) hci_uart(E) btqca(E) btrtl(E) btbcm(E) btintel(E) bluetooth(E) nls_ascii(E) nls_cp437(E) vfat(E) fat(E) bcm2835_v4l2(CE) bcm2835_mmal_vchiq(CE) videobuf2_vmalloc(E) videobuf2_memops(E) sha512_generic(E) videobuf2_v4l2(E) sha512_arm(E) videobuf2_common(E) videodev(E) cpufreq_dt(E) snd_bcm2835(CE) brcmfmac(E) mc(E) vc4(E) ctr(E) brcmutil(E) snd_soc_core(E) snd_pcm_dmaengine(E) drbg(E) snd_pcm(E) snd_timer(E) snd(E) soundcore(E) drm_kms_helper(E) cec(E) ansi_cprng(E) rc_core(E) syscopyarea(E) raspberrypi_cpufreq(E) sysfillrect(E) sysimgblt(E) cfg80211(E) max17040_battery(OE) raspberrypi_hwmon(E) fb_sys_fops(E) regmap_i2c(E) ecdh_generic(E) rfkill(E) ecc(E) bcm2835_rng(E) rng_core(E) vchiq(CE) leds_gpio(E) libcomposite(E) fuse(E) configfs(E) ip_tables(E) x_tables(E) autofs4(E) ext4(E) crc16(E) mbcache(E) jbd2(E) crc32c_generic(E) sdhci_iproc(E) sdhci_pltfm(E) sdhci(E) [ 1946.399633] CPU: 0 PID: 431 Comm: smartcard-openp Tainted: G C OE 5.15.0-1-rpi #1 Debian 5.15.3-1 [ 1946.417950] Hardware name: BCM2835 [ 1946.425442] Backtrace: [ 1946.432048] [<c08d60a0>] (dump_backtrace) from [<c08d62ec>] (show_stack+0x20/0x24) [ 1946.448226] r7:00000009 r6:0000001c r5:c04a948c r4:c0a64e2c [ 1946.458412] [<c08d62cc>] (show_stack) from [<c08d9ae0>] (dump_stack+0x28/0x30) [ 1946.470380] [<c08d9ab8>] (dump_stack) from [<c0123500>] (__warn+0xe8/0x154) [ 1946.482067] r5:c04a948c r4:c0a71dc8 [ 1946.490184] [<c0123418>] (__warn) from [<c08d6948>] (warn_slowpath_fmt+0xa0/0xe4) [ 1946.506758] r7:00000009 r6:0000001c r5:c0a71dc8 r4:c0a71e04 [ 1946.517070] [<c08d68ac>] (warn_slowpath_fmt) from [<c04a948c>] (refcount_warn_saturate+0x110/0x15c) [ 1946.535309] r8:c0100224 r7:c0dfcb84 r6:ffffffff r5:c3b84c00 r4:c24a17c0 [ 1946.546708] [<c04a937c>] (refcount_warn_saturate) from [<c0380134>] (eventfd_ctx_put+0x48/0x74) [ 1946.564476] [<c03800ec>] (eventfd_ctx_put) from [<bf5464e8>] (ffs_data_clear+0xd0/0x118 [usb_f_fs]) [ 1946.582664] r5:c3b84c00 r4:c2695b00 [ 1946.590668] [<bf546418>] (ffs_data_clear [usb_f_fs]) from [<bf547cc0>] (ffs_data_closed+0x9c/0x150 [usb_f_fs]) [ 1946.609608] r5:bf54d014 r4:c2695b00 [ 1946.617522] [<bf547c24>] (ffs_data_closed [usb_f_fs]) from [<bf547da0>] (ffs_fs_kill_sb+0x2c/0x30 [usb_f_fs]) [ 1946.636217] r7:c0dfcb84 r6:c3a12260 r5:bf54d014 r4:c229f000 [ 1946.646273] [<bf547d74>] (ffs_fs_kill_sb [usb_f_fs]) from [<c0326d50>] (deactivate_locked_super+0x54/0x9c) [ 1946.664893] r5:bf54d014 r4:c229f000 [ 1946.672921] [<c0326cfc>] (deactivate_locked_super) from [<c0326df8>] (deactivate_super+0x60/0x64) [ 1946.690722] r5:c2a09000 r4:c229f000 [ 1946.698706] [<c0326d98>] (deactivate_super) from [<c0349a28>] (cleanup_mnt+0xe4/0x14c) [ 1946.715553] r5:c2a09000 r4:00000000 [ 1946.723528] [<c0349944>] (cleanup_mnt) from [<c0349b08>] (__cleanup_mnt+0x1c/0x20) [ 1946.739922] r7:c0dfcb84 r6:c3a12260 r5:c3a126fc r4:00000000 [ 1946.750088] [<c0349aec>] (__cleanup_mnt) from [<c0143d10>] (task_work_run+0x84/0xb8) [ 1946.766602] [<c0143c8c>] (task_work_run) from [<c010bdc8>] (do_work_pending+0x470/0x56c) [ 1946.783540] r7:5ac3c35a r6:c0d0424c r5:c200bfb0 r4:c200a000 [ 1946.793614] [<c010b958>] (do_work_pending) from [<c01000c0>] (slow_work_pending+0xc/0x20) [ 1946.810553] Exception stack(0xc200bfb0 to 0xc200bff8) [ 1946.820129] bfa0: 00000000 00000000 000000aa b5e21430 [ 1946.837104] bfc0: bef867a0 00000001 bef86840 00000034 bef86838 bef86790 bef86794 bef867a0 [ 1946.854125] bfe0: 00000000 bef86798 b67b7a1c b6d626a4 60000010 b5a23760 [ 1946.865335] r10:00000000 r9:c200a000 r8:c0100224 r7:00000034 r6:bef86840 r5:00000001 [ 1946.881914] r4:bef867a0 [ 1946.888793] ---[ end trace 7387f2a9725b28d0 ]--- Fixes: 5e33f6fd ("usb: gadget: ffs: add eventfd notification about ffs events") Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Mathias Nyman authored
commit e4844092 upstream. The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like other Fresco controllers, but should not have the BROKEN_MSI quirks set. BROKEN_MSI quirk causes issues in detecting usb drives connected to docks with this FL1100 controller. The BROKEN_MSI flag was apparently accidentally set together with the TRUST_TX_LENGTH quirk Original patch went to stable so this should go there as well. Fixes: ea0f69d8 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller") Cc: stable@vger.kernel.org cc: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by:
-
Angus Wang authored
commit ee2698cf upstream. [WHY] Current implementation of pipe split policy prevents pipe split with multiple displays connected, which caused the MCLK speed to be stuck at max [HOW] Changed the pipe split policies so that pipe split is allowed for multi-display configurations Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1522 Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1709 Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1655 Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1403 Note this is a backport of this commit from amdgpu drm-next for 5.16. Tested-by:
-
Alex Deucher authored
commit 5e713c6a upstream. Used on gfx9 based systems. Fixes incorrect CU counts reported in the kernel log. Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1833 Reviewed-by:
-
chen gong authored
commit b7865173 upstream. Play a video on the raven (or PCO, raven2) platform, and then do the S3 test. When resume, the following error will be reported: amdgpu 0000:02:00.0: [drm:amdgpu_ring_test_helper [amdgpu]] *ERROR* ring vcn_dec test failed (-110) [drm:amdgpu_device_ip_resume_phase2 [amdgpu]] *ERROR* resume of IP block <vcn_v1_0> failed -110 amdgpu 0000:02:00.0: amdgpu: amdgpu_device_ip_resume failed (-110). PM: dpm_run_callback(): pci_pm_resume+0x0/0x90 returns -110 [why] When playing the video: The power state flag of the vcn block is set to POWER_STATE_ON. When doing suspend: There is no change to the power state flag of the vcn block, it is still POWER_STATE_ON. When doing resume: Need to open the power gate of the vcn block and set the power state flag of the VCN block to POWER_STATE_ON. But at this time, the power state flag of the vcn block is already POWER_STATE_ON. The power status flag check in the "8f2cdef drm/amd/pm: avoid duplicate powergate/ungate setting" patch will return the amdgpu_dpm_set_powergating_by_smu function directly. As a result, the gate of the power was not opened, causing the subsequent ring test to fail. [how] In the suspend function of the vcn block, explicitly change the power state flag of the vcn block to POWER_STATE_OFF. BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1828 Signed-off-by:
-
Christian König authored
commit 67f74302 upstream. Always waiting for the exclusive fence resulted on some performance regressions. So try to wait for the shared fences first, then the exclusive fence should always be signaled already. v2: fix incorrectly placed "(", add some comment why we do this. Signed-off-by:
-
Dmitry V. Levin authored
commit 7175f02c upstream. Replace sa_family_t with __kernel_sa_family_t to fix the following linux/nfc.h userspace compilation errors: /usr/include/linux/nfc.h:266:2: error: unknown type name 'sa_family_t' sa_family_t sa_family; /usr/include/linux/nfc.h:274:2: error: unknown type name 'sa_family_t' sa_family_t sa_family; Fixes: 23b7869c ("NFC: add the NFC socket raw protocol") Fixes: d646960f ("NFC: Initial LLCP support") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Krzysztof Kozlowski authored
commit 79b69a83 upstream. Fix user-space builds if it includes /usr/include/linux/nfc.h before some of other headers: /usr/include/linux/nfc.h:281:9: error: unknown type name ‘size_t’ 281 | size_t service_name_len; | ^~~~~~ Fixes: d646960f ("NFC: Initial LLCP support") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Pavel Skripkin authored
[ Upstream commit bb436283 ] Wrong user data may cause warning in i2c_transfer(), ex: zero msgs. Userspace should not be able to trigger warnings, so this patch adds validation checks for user data in compact ioctl to prevent reported warnings Reported-and-tested-by:
-
Miaoqian Lin authored
[ Upstream commit bf2b09fe ] The reference taken by 'of_find_device_by_node()' must be released when not needed anymore. Add the corresponding 'put_device()' in the and error handling paths. Fixes: 18a6c85f ("fsl/fman: Add FMan Port Support") Signed-off-by:
-
Jianguo Wu authored
[ Upstream commit 8b3170e0 ] udpgro_fwd.sh output following message: ping: 2001:db8:1::100: Address family for hostname not supported Using ping6 when pinging IPv6 addresses. Fixes: a062260a ("selftests: net: add UDP GRO forwarding self-tests") Signed-off-by:
-
Jiasheng Jiang authored
[ Upstream commit 92a34ab1 ] As we can see from the comment of the nla_put() that it could return -EMSGSIZE if the tailroom of the skb is insufficient. Therefore, it should be better to check the return value of the nla_put_u32 and return the error code if error accurs. Also, there are many other functions have the same problem, and if this patch is correct, I will commit a new version to fix all. Fixes: 955dc68c ("net/ncsi: Add generic netlink family") Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 168fed98 ] We need to first check if the context is a vlan one, then we need to check the global bridge multicast vlan snooping flag, and finally the vlan's multicast flag, otherwise we will unnecessarily enable vlan mcast processing (e.g. querier timers). Fixes: 7b54aaaf ("net: bridge: multicast: add vlan state initialization and control") Signed-off-by:
-
Jianguo Wu authored
[ Upstream commit add25d6d ] $rvs -> $rcv Fixes: a062260a ("selftests: net: add UDP GRO forwarding self-tests") Signed-off-by:
-
wujianguo authored
[ Upstream commit 9c1952ae ] udpgso_bench_tx call setup_sockaddr() for dest address before parsing all arguments, if we specify "-p ${dst_port}" after "-D ${dst_ip}", then ${dst_port} will be ignored, and using default cfg_port 8000. This will cause test case "multiple GRO socks" failed in udpgro.sh. Setup sockaddr after parsing all arguments. Fixes: 3a687bef ("selftests: udp gso benchmark") Signed-off-by:
-
Nikolay Aleksandrov authored
[ Upstream commit f83a112b ] As reported[1] if startup query interval is set too low in combination with large number of startup queries and we have multiple bridges or even a single bridge with multiple querier vlans configured we can crash the machine. Add a 1 second minimum which must be enforced by overwriting the value if set lower (i.e. without returning an error) to avoid breaking user-space. If that happens a log message is emitted to let the admin know that the startup interval has been set to the minimum. It doesn't make sense to make the startup interval lower than the normal query interval so use the same value of 1 second. The issue has been present since these intervals could be user-controlled. [1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/ Fixes: d902eee4 ("bridge: Add multicast count/interval sysfs entries") Reported-by:
-
Nikolay Aleksandrov authored
[ Upstream commit 99b40610 ] As reported[1] if query interval is set too low and we have multiple bridges or even a single bridge with multiple querier vlans configured we can crash the machine. Add a 1 second minimum which must be enforced by overwriting the value if set lower (i.e. without returning an error) to avoid breaking user-space. If that happens a log message is emitted to let the administrator know that the interval has been set to the minimum. The issue has been present since these intervals could be user-controlled. [1] https://lore.kernel.org/netdev/e8b9ce41-57b9-b6e2-a46a-ff9c791cf0ba@gmail.com/ Fixes: d902eee4 ("bridge: Add multicast count/interval sysfs entries") Reported-by:
-
Gal Pressman authored
[ Upstream commit 992d8a4e ] In case of an error in mlx5e_set_features(), 'netdev->features' must be updated with the correct state of the device to indicate which features were updated successfully. To do that we maintain a copy of 'netdev->features' and update it after successful feature changes, so we can assign it to back to 'netdev->features' if needed. However, since not all netdev features are handled by the driver (e.g. GRO/TSO/etc), some features may not be updated correctly in case of an error updating another feature. For example, while requesting to disable TSO (feature which is not handled by the driver) and enable HW-GRO, if an error occurs during HW-GRO enable, 'oper_features' will be assigned with 'netdev->features' and HW-GRO turned off. TSO will remain enabled in such case, which is a bug. To solve that, instead of using 'netdev->features' as the baseline of 'oper_features' and changing it on set feature success, use 'features' instead and update it in case of errors. Fixes: 75b81ce7 ("net/mlx5e: Don't override netdev features field unless in error flow") Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 140c7bc7 ] When allocated, this bitmap is not initialized. Only the first bit is set a few lines below. Use bitmap_zalloc() to make sure that it is cleared before being used. Fixes: 6461b446 ("ionic: Add interrupts and doorbells") Signed-off-by:
-
Nicholas Kazlauskas authored
[ Upstream commit 33735c1c ] [Why] We'll exit optimized power state to do link detection but we won't enter back into the optimized power state. This could potentially block s2idle entry depending on the sequencing, but it also means we're losing some power during the transition period. [How] Hook up the handler like DCN21. It was also missed like the exit_optimized_pwr_state callback. Fixes: 64b1d0e8 ("drm/amd/display: Add DCN3.1 HWSEQ") Tested-by:
-
Nicholas Kazlauskas authored
[ Upstream commit a07f8b99 ] [Why] Otherwise SMU won't mark Display as idle when trying to perform s2idle. [How] Mark the bit in the dcn31 codepath, doesn't apply to older ASIC. It needed to be split from phy refclk off to prevent entering s2idle when PSR was engaged but driver was not ready. Fixes: 118a3315 ("drm/amd/display: Add DCN3.1 clock manager support") Tested-by:
-
James McLaughlin authored
[ Upstream commit f85846bb ] Time synchronization was not properly enabled on non-MSI-X platforms. Fixes: 2c344ae2 ("igc: Add support for TX timestamping") Signed-off-by:
-
Vinicius Costa Gomes authored
[ Upstream commit 1e81dcc1 ] It was reported that when PCIe PTM is enabled, some lockups could be observed with some integrated i225-V models. While the issue is investigated, we can disable crosstimestamp for those models and see no loss of functionality, because those models don't have any support for time synchronization. Fixes: a90ec848 ("igc: Add support for PTP getcrosststamp()") Link: https://lore.kernel.org/all/924175a188159f4e03bd69908a91e606b574139b.camel@gmx.de/ Reported-by:
-
Dust Li authored
[ Upstream commit 349d4312 ] A crash occurs when smc_cdc_tx_handler() tries to access smc_sock but smc_release() has already freed it. [ 4570.695099] BUG: unable to handle page fault for address: 000000002eae9e88 [ 4570.696048] #PF: supervisor write access in kernel mode [ 4570.696728] #PF: error_code(0x0002) - not-present page [ 4570.697401] PGD 0 P4D 0 [ 4570.697716] Oops: 0002 [#1] PREEMPT SMP NOPTI [ 4570.698228] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.16.0-rc4+ #111 [ 4570.699013] Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 8c24b4c 04/0 [ 4570.699933] RIP: 0010:_raw_spin_lock+0x1a/0x30 <...> [ 4570.711446] Call Trace: [ 4570.711746] <IRQ> [ 4570.711992] smc_cdc_tx_handler+0x41/0xc0 [ 4570.712470] smc_wr_tx_tasklet_fn+0x213/0x560 [ 4570.712981] ? smc_cdc_tx_dismisser+0x10/0x10 [ 4570.713489] tasklet_action_common.isra.17+0x66/0x140 [ 4570.714083] __do_softirq+0x123/0x2f4 [ 4570.714521] irq_exit_rcu+0xc4/0xf0 [ 4570.714934] common_interrupt+0xba/0xe0 Though smc_cdc_tx_handler() checked the existence of smc connection, smc_release() may have already dismissed and released the smc socket before smc_cdc_tx_handler() further visits it. smc_cdc_tx_handler() |smc_release() if (!conn) | | |smc_cdc_tx_dismiss_slots() | smc_cdc_tx_dismisser() | |sock_put(&smc->sk) <- last sock_put, | smc_sock freed bh_lock_sock(&smc->sk) (panic) | To make sure we won't receive any CDC messages after we free the smc_sock, add a refcount on the smc_connection for inflight CDC message(posted to the QP but haven't received related CQE), and don't release the smc_connection until all the inflight CDC messages haven been done, for both success or failed ones. Using refcount on CDC messages brings another problem: when the link is going to be destroyed, smcr_link_clear() will reset the QP, which then remove all the pending CQEs related to the QP in the CQ. To make sure all the CQEs will always come back so the refcount on the smc_connection can always reach 0, smc_ib_modify_qp_reset() was replaced by smc_ib_modify_qp_error(). And remove the timeout in smc_wr_tx_wait_no_pending_sends() since we need to wait for all pending WQEs done, or we may encounter use-after- free when handling CQEs. For IB device removal routine, we need to wait for all the QPs on that device been destroyed before we can destroy CQs on the device, or the refcount on smc_connection won't reach 0 and smc_sock cannot be released. Fixes: 5f08318f ("smc: connection data control (CDC)") Reported-by:
-
Dust Li authored
[ Upstream commit 90cee52f ] We found smc_llc_send_link_delete_all() sometimes wait for 2s timeout when testing with RDMA link up/down. It is possible when a smc_link is in ACTIVATING state, the underlaying QP is still in RESET or RTR state, which cannot send any messages out. smc_llc_send_link_delete_all() use smc_link_usable() to checks whether the link is usable, if the QP is still in RESET or RTR state, but the smc_link is in ACTIVATING, this LLC message will always fail without any CQE entering the CQ, and we will always wait 2s before timeout. Since we cannot send any messages through the QP before the QP enter RTS. I add a wrapper smc_link_sendable() which checks the state of QP along with the link state. And replace smc_link_usable() with smc_link_sendable() in all LLC & CDC message sending routine. Fixes: 5f08318f ("smc: connection data control (CDC)") Signed-off-by:
-
Wei Yongjun authored
[ Upstream commit 1b9dadba ] 'phy->pending_skb' is alloced when device probe, but forgot to free in the error handling path and remove path, this cause memory leak as follows: unreferenced object 0xffff88800bc06800 (size 512): comm "8", pid 11775, jiffies 4295159829 (age 9.032s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000d66c09ce>] __kmalloc_node_track_caller+0x1ed/0x450 [<00000000c93382b3>] kmalloc_reserve+0x37/0xd0 [<000000005fea522c>] __alloc_skb+0x124/0x380 [<0000000019f29f9a>] st21nfca_hci_i2c_probe+0x170/0x8f2 Fix it by freeing 'pending_skb' in error and remove. Fixes: 68957303 ("NFC: ST21NFCA: Add driver for STMicroelectronics ST21NFCA NFC Chip") Reported-by:
-
Aleksander Jan Bajkowski authored
[ Upstream commit 5be60a94 ] Received frames have FCS truncated. There is no need to subtract FCS length from the statistics. Fixes: fe1a5642 ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver") Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit 1cd5384c ] 'ndev' is a managed resource allocated with devm_alloc_etherdev(), so there is no need to call free_netdev() explicitly or there will be a double free(). Simplify all error handling paths accordingly. Fixes: d51b6ce4 ("net: ethernet: add ag71xx driver") Signed-off-by:
-
Matthias-Christian Ott authored
[ Upstream commit ca506fca ] The D-Link DSB-650TX (2001:4002) is unable to receive Ethernet frames that are longer than 1518 octets, for example, Ethernet frames that contain 802.1Q VLAN tags. The frames are sent to the pegasus driver via USB but the driver discards them because they have the Long_pkt field set to 1 in the received status report. The function read_bulk_callback of the pegasus driver treats such received "packets" (in the terminology of the hardware) as errors but the field simply does just indicate that the Ethernet frame (MAC destination to FCS) is longer than 1518 octets. It seems that in the 1990s there was a distinction between "giant" (> 1518) and "runt" (< 64) frames and the hardware includes flags to indicate this distinction. It seems that the purpose of the distinction "giant" frames was to not allow infinitely long frames due to transmission errors and to allow hardware to have an upper limit of the frame size. However, the hardware already has such limit with its 2048 octet receive buffer and, therefore, Long_pkt is merely a convention and should not be treated as a receive error. Actually, the hardware is even able to receive Ethernet frames with 2048 octets which exceeds the claimed limit frame size limit of the driver of 1536 octets (PEGASUS_MTU). Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Karsten Graul authored
[ Upstream commit 6d7373da ] In smc_wr_tx_send_wait() the completion on index specified by pend->idx is initialized and after smc_wr_tx_send() was called the wait for completion starts. pend->idx is used to get the correct index for the wait, but the pend structure could already be cleared in smc_wr_tx_process_cqe(). Introduce pnd_idx to hold and use a local copy of the correct index. Fixes: 09c61d24 ("net/smc: wait for departure of an IB message") Signed-off-by:
-
Xin Long authored
[ Upstream commit 5ec7d18d ] This patch is to delay the endpoint free by calling call_rcu() to fix another use-after-free issue in sctp_sock_dump(): BUG: KASAN: use-after-free in __lock_acquire+0x36d9/0x4c20 Call Trace: __lock_acquire+0x36d9/0x4c20 kernel/locking/lockdep.c:3218 lock_acquire+0x1ed/0x520 kernel/locking/lockdep.c:3844 __raw_spin_lock_bh include/linux/spinlock_api_smp.h:135 [inline] _raw_spin_lock_bh+0x31/0x40 kernel/locking/spinlock.c:168 spin_lock_bh include/linux/spinlock.h:334 [inline] __lock_sock+0x203/0x350 net/core/sock.c:2253 lock_sock_nested+0xfe/0x120 net/core/sock.c:2774 lock_sock include/net/sock.h:1492 [inline] sctp_sock_dump+0x122/0xb20 net/sctp/diag.c:324 sctp_for_each_transport+0x2b5/0x370 net/sctp/socket.c:5091 sctp_diag_dump+0x3ac/0x660 net/sctp/diag.c:527 __inet_diag_dump+0xa8/0x140 net/ipv4/inet_diag.c:1049 inet_diag_dump+0x9b/0x110 net/ipv4/inet_diag.c:1065 netlink_dump+0x606/0x1080 net/netlink/af_netlink.c:2244 __netlink_dump_start+0x59a/0x7c0 net/netlink/af_netlink.c:2352 netlink_dump_start include/linux/netlink.h:216 [inline] inet_diag_handler_cmd+0x2ce/0x3f0 net/ipv4/inet_diag.c:1170 __sock_diag_cmd net/core/sock_diag.c:232 [inline] sock_diag_rcv_msg+0x31d/0x410 net/core/sock_diag.c:263 netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2477 sock_diag_rcv+0x2a/0x40 net/core/sock_diag.c:274 This issue occurs when asoc is peeled off and the old sk is freed after getting it by asoc->base.sk and before calling lock_sock(sk). To prevent the sk free, as a holder of the sk, ep should be alive when calling lock_sock(). This patch uses call_rcu() and moves sock_put and ep free into sctp_endpoint_destroy_rcu(), so that it's safe to try to hold the ep under rcu_read_lock in sctp_transport_traverse_process(). If sctp_endpoint_hold() returns true, it means this ep is still alive and we have held it and can continue to dump it; If it returns false, it means this ep is dead and can be freed after rcu_read_unlock, and we should skip it. In sctp_sock_dump(), after locking the sk, if this ep is different from tsp->asoc->ep, it means during this dumping, this asoc was peeled off before calling lock_sock(), and the sk should be skipped; If this ep is the same with tsp->asoc->ep, it means no peeloff happens on this asoc, and due to lock_sock, no peeloff will happen either until release_sock. Note that delaying endpoint free won't delay the port release, as the port release happens in sctp_endpoint_destroy() before calling call_rcu(). Also, freeing endpoint by call_rcu() makes it safe to access the sk by asoc->base.sk in sctp_assocs_seq_show() and sctp_rcv(). Thanks Jones to bring this issue up. v1->v2: - improve the changelog. - add kfree(ep) into sctp_endpoint_destroy_rcu(), as Jakub noticed. Reported-by:
-
Coco Li authored
[ Upstream commit 5471d522 ] The below referenced commit correctly updated the computation of number of segments (gso_size) by using only the gso payload size and removing the header lengths. With this change the regression test started failing. Update the tests to match this new behavior. Both IPv4 and IPv6 tests are updated, as a separate patch in this series will update udp_v6_send_skb to match this change in udp_send_skb. Fixes: 158390e4 ("udp: using datalen to cap max gso segments") Signed-off-by:
-
Coco Li authored
[ Upstream commit 736ef37f ] The max number of UDP gso segments is intended to cap to UDP_MAX_SEGMENTS, this is checked in udp_send_skb(). skb->len contains network and transport header len here, we should use only data len instead. This is the ipv6 counterpart to the below referenced commit, which missed the ipv6 change Fixes: 158390e4 ("udp: using datalen to cap max gso segments") Signed-off-by:
-
Chris Mi authored
[ Upstream commit 2820110d ] When there is ct or sample action, the ct or sample rule will be deleted and return. But if there is an extra mirror action, the forward rule can't be deleted because of the return. Fix it by removing the return. Fixes: 69e2916e ("net/mlx5: CT: Add support for mirroring") Fixes: f94d6389 ("net/mlx5e: TC, Add support to offload sample action") Signed-off-by:
-
Roi Dayan authored
[ Upstream commit f3e02e47 ] Instead of having sparse ifdefs in source files use a single ifdef in the tc sample header file and use stubs. Signed-off-by:
-
Maxim Mikityanskiy authored
[ Upstream commit 19c4aba2 ] There are two ICOSQs per channel: one is needed for RX, and the other for async operations (XSK TX, kTLS offload). Currently, the recovery flow for both is the same, and async ICOSQ is mistakenly treated like the regular ICOSQ. This patch prevents running the regular ICOSQ recovery on async ICOSQ. The purpose of async ICOSQ is to handle XSK wakeup requests and post kTLS offload RX parameters, it has nothing to do with RQ and XSKRQ UMRs, so the regular recovery sequence is not applicable here. Fixes: be5323c8 ("net/mlx5e: Report and recover from CQE error on ICOSQ") Signed-off-by:
-
Maxim Mikityanskiy authored
[ Upstream commit 17958d7c ] Both regular RQ and XSKRQ use the same ICOSQ for UMRs. When doing recovery for the ICOSQ, don't forget to deactivate XSKRQ. XSK can be opened and closed while channels are active, so a new mutex prevents the ICOSQ recovery from running at the same time. The ICOSQ recovery deactivates and reactivates XSKRQ, so any parallel change in XSK state would break consistency. As the regular RQ is running, it's not enough to just flush the recovery work, because it can be rescheduled. Fixes: be5323c8 ("net/mlx5e: Report and recover from CQE error on ICOSQ") Signed-off-by:
-
Amir Tzin authored
[ Upstream commit 918fc385 ] Function mlx5e_tx_reporter_dump_sq() casts its void * argument to struct mlx5e_txqsq *, but in TX-timeout-recovery flow the argument is actually of type struct mlx5e_tx_timeout_ctx *. mlx5_core 0000:08:00.1 enp8s0f1: TX timeout detected mlx5_core 0000:08:00.1 enp8s0f1: TX timeout on queue: 1, SQ: 0x11ec, CQ: 0x146d, SQ Cons: 0x0 SQ Prod: 0x1, usecs since last trans: 21565000 BUG: stack guard page was hit at 0000000093f1a2de (stack is 00000000b66ea0dc..000000004d932dae) kernel stack overflow (page fault): 0000 [#1] SMP NOPTI CPU: 5 PID: 95 Comm: kworker/u20:1 Tainted: G W OE 5.13.0_mlnx #1 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014 Workqueue: mlx5e mlx5e_tx_timeout_work [mlx5_core] RIP: 0010:mlx5e_tx_reporter_dump_sq+0xd3/0x180 [mlx5_core] Call Trace: mlx5e_tx_reporter_dump+0x43/0x1c0 [mlx5_core] devlink_health_do_dump.part.91+0x71/0xd0 devlink_health_report+0x157/0x1b0 mlx5e_reporter_tx_timeout+0xb9/0xf0 [mlx5_core] ? mlx5e_tx_reporter_err_cqe_recover+0x1d0/0x1d0 [mlx5_core] ? mlx5e_health_queue_dump+0xd0/0xd0 [mlx5_core] ? update_load_avg+0x19b/0x550 ? set_next_entity+0x72/0x80 ? pick_next_task_fair+0x227/0x340 ? finish_task_switch+0xa2/0x280 mlx5e_tx_timeout_work+0x83/0xb0 [mlx5_core] process_one_work+0x1de/0x3a0 worker_thread+0x2d/0x3c0 ? process_one_work+0x3a0/0x3a0 kthread+0x115/0x130 ? kthread_park+0x90/0x90 ret_from_fork+0x1f/0x30 --[ end trace 51ccabea504edaff ]--- RIP: 0010:mlx5e_tx_reporter_dump_sq+0xd3/0x180 PKRU: 55555554 Kernel panic - not syncing: Fatal exception Kernel Offset: disabled end Kernel panic - not syncing: Fatal exception To fix this bug add a wrapper for mlx5e_tx_reporter_dump_sq() which extracts the sq from struct mlx5e_tx_timeout_ctx and set it as the TX-timeout-recovery flow dump callback. Fixes: 5f29458b ("net/mlx5e: Support dump callback in TX reporter") Signed-off-by:
-